background image

Technical data

Total connected load: 3 000 W
AC 208/220-240 V / 60 Hz

Important notes on installation

This appliance can be combined with all Gaggenau   
Vario 400 Series appliances. 

Note: do not install the appliance directly next
to a steam cooker!

This appliance may be installed in kitchen combi-
nations made of wood or similar combustible 
materials without taking additional safety measures.
The built-in furniture and worktop where the 
appliance is installed must be heat resistant up to
temperatures of 200° F/90° C.

The appliance must only be connected by an 
authorised specialist, paying attention to the 
relevant regulations of the power supply companies
and the regional construction regulations.

When connecting electrical appliances in the 
proximity of cooking surfaces, make sure that
connecting cables do not come into contact with 
hot cooking surfaces.

The installation technician is responsible for the
correct functioning of the appliance at the place of
installation. He must instruct the user on how to 
disconnect the appliance from electricity in an
emergency.

After unpacking, check the appliance for any 
transportation damage and report this immediately
to the transportation company.  

There must be a gap of at least 40 mm (1

9

/

16

´ ´ ) at 

the side between the appliance and any walls or
furnishings. 

The minimum distance from the trough base to the
nearest heat-sensitive parts is 10 mm (

13

/

32

´ ´ ).

If all poles of the appliances cannot be isolated
from the mains by removing an accessible plug, an
isolating device with a contact gap of at least 3 mm
must be installed (e.g. domestic fuse).

Only a qualified electrician should install this 
appliance.

This appliance must be hardwired. 
The mains connecting cable must at least 
correspond to the type SJTO 3x16 AWG 105°C.
The mains connecting cable must only be
purchased through and connected by an 
authorised specialist. The appliance must be
properly grounded. Pay attention to the 
information on the rating plate.

No warranty claims can be lodged for any 
damage resulting from failure to observe these
instructions. Pay attention to the “Important
notes" on page 3 and 4.

Subject to technical change without notice.

15

8. Installation

Summary of Contents for VF 411-610

























Reviews: