GAH Electrastream User And Installation Manual Download

Page: 18 / 56

Important Health and Safety Information for Installers and Service Engineers

Health and Safety at Work Act 1974
Consumer Protection Act 1987
COSHH Regulations 1988
The following information is given as a requirement of the
above legislation.
Great care is taken by GAH (HEATING PRODUCTS) LIMITED
to ensure that Electrastream systems are designed and
manufactured to meet general safety requirements when
properly used and installed as recommended in this manual.
It is the responsibility of Users and Engineers to ensure that
adequate protective clothing and glasses are worn when
working with the Electrastream system.

SEALS AND INSULATION

SEALS AND INSULATION
Insulation and sealing materials are used in the construction
of the Electrastream cylinders. Units are sealed and when
used in the manner for which they are intended the insulating
and sealing materials do not present any known hazard.
However always observe the following recommendations:-
1. Avoid inhalation of fibres or dust, wear face mask.
2. Avoid eye contamination by fibres or dust - wear eye
protection.
3. As far as possible avoid any skin contact with Fibreglass
Insulation, Glass Rope, Mineral Wool, Insulation Pads and
Ceramic Fibre.

PPPPPatent application 01514800.2

atent application 01514800.2

2010 GAH (HEATING PRODUCTS) L

2010 GAH (HEATING PRODUCTS) LTD.

TD.

Electrastr

Electrastream is a T

eam is a T

eam is a Trademark of GAH (HEATING PRODUCTS) L

rademark of GAH (HEATING PRODUCTS) L

rademark of GAH (HEATING PRODUCTS) LTD.

TD.

Manual by Harber Technical Services Tel/Fax 01263 515444

E-mail:info@harbertech.co.uk www.harbertech.co.uk

GAH (Heating Pr

GAH (Heating Products) Ltd.

oducts) Ltd.

Building 846
Bentwaters Parks
Rendlesham
Woodbridge
Suffolk IP12 2TW

TTTTTel:

el:

el: 01394 421160

01394 421160

Fax:

Fax: 01394 421170

01394 421170

email: mail@gah.co.uk
www.gah.co.uk

In pursuance of a policy of constant development, GAH (HEATING PRODUCTS) LIMITED
reserve the right to change Electrastream parts or design without notice, therefore
certain details included in this manual may not be correct at the time of printing. Any
modification and improvements detailed in this manual does not commit GAH to update
any system previously supplied.

Manual Part No. ...................MAN1019
Manual Ref ..........................ES02
Issue ...................................13
Date ....................................25/02/13

GAH (HEATING PRODUCTS) LIMITED will not accept

responsibility for any damage or personal injury caused

by not giving due consideration to the above safety

recommendations.

OTHER MATERIALS

SEALANTS, ADHESIVES AND PAINTS

Sealants, Adhesives and Paints are used in the construction of
the Electrastream components. When used in the manner for
which they are intended they do not present any known hazard.

ELECTRIC

ELECTRIC
The Cylinder Tri-Core Heater, Pump, Thermostats and Contactor
Box all have electrical supply of 230V (enough to endanger
life).
Always isolate before connection, adjustment, servicing and
repair.
When the Tri-Core Heater cover is removed high power live
electrical terminals are exposed.
ISOLATE THE TRI-CORE HEATER BEFORE REMOVING ITS
COVER.
Earth protection - Earth Continuity Conductors must be fitted
and must comply with IEE Wiring Regulations.

HTS REF GAH ELECTRASTREAM 25/02/13

HEAL

HEALTH & SAFETY

TH & SAFETY

2-2.3 Error Displays

When any of the following errors are displayed call service engineer.
ERROR 1
When ‘Error 1’ is displayed it indicates a faulty or disconnected temperature sensor.
Heating is disabled.
ERROR 2
When ‘Error 2’ is displayed it indicates:-
1.

The auxiliary 5 amp fuse has blown, or

The pump, motorised valve or room thermostat is faulty, or

Heating is disabled.
ERROR 3
When ‘Error 3’ is displayed it indicates that all heater elements failed heater test.
Heating is disabled.
ERROR 5
One or more of the controller ‘set’, ‘up’, ‘down’ or ‘boost’ buttons is stuck or held down.
HEAT 1 ! ! ! ! !
When !!!!! is displayed under Heat 1, Heat 2 or Heat 3 it indicates a tri-core element has

failed. Check the resettable thermal trips in the Electrastream Control Unit - see 2-2.4.

2-2.4 Element Resettable Thermal Trips

Each of the three elements of the tri-core heater is protected by a 16amp Resettable
Thermal Trip, these have their reset buttons located on the front of the Electrastream
Control Unit.
In the event of electrical overload on an element the relevant thermal trip will trip out,
when this occurs the button will pop out. Also the control screen will display ‘!’ under
Heat 1, Heat 2, and/or Heat 3 see fig. 2-2a.
To reset the thermal trip:-
1.

Turn OFF the Electrastream mains isolating switch - see 2-1.1.

Look at the three buttons; button/s that are protruding have tripped out.

Press the button in, if the button stays in when the power is turned on, then trip has
been reset. However if the button pops out again a possible fault exists - contact
the installer.

The Electrastream will still operate with one or two elements working, but this is not
satisfactory and the installer must be contacted to rectify the fault as soon as possible.

2-2.5 Economy Tariffs

Regional electricity suppliers have their own ‘Off-Peak’ tariffs that will provide an
economical supply of power for the Electrastream system.
It is vital that the time settings of the Electrastream control unit are set to make the most
use of the available ‘Off-Peak’ tariffs.

2-2.6 Normal Tariffs

Normal tariffs are at all times that are not designated for ‘Off-Peak’, the cost of electricity
during normal times will be more expensive. Therefore avoid setting heating and hot
water ON during these periods.

OPERA

OPERATOR CONTROLS 2

TOR CONTROLS 2