background image

Pub.  42004-703L2A 

GAI-Tronics Corporation  P.O. Box 1060, Reading, PA  19607-1060  USA 

610-777-1374  

„

  800-492-1212  

„

  Fax:  610-796-5954 

V

ISIT WWW

.

GAI

-

TRONICS

.

COM FOR PRODUCT LITERATURE AND MANUALS

 

 

G A I - T R O N I C S ®   C O R P O R A T I O N  

A   H U B B E L L   C O M P A N Y  

Model 707-001-EX-F07045 

SmartSeries Hazardous Area 

Speaker Amplifier Enclosure 

Confidentiality Notice 

This manual is provided solely as an operational, installation, and maintenance guide and contains sensitive 
business and technical information that is confidential and proprietary to GAI-Tronics.  GAI-Tronics 
retains all intellectual property and other rights in or to the information contained herein, and such 
information may only be used in connection with the operation of your GAI-Tronics product or system.  
This manual may not be disclosed in any form, in whole or in part, directly or indirectly, to any third party. 

General Information 

The Model 707-001-EX Speaker Amplifier Enclosure is a component of the 700 Series Page/Party

<

 

system.  It is constructed of cast aluminum and is extremely weatherproof and corrosion-resistant.  This 
enclosure is equipped with terminal strips for connecting system cable.  The Model 709-901 SmartSeries 
Amplifier mates directly with this enclosure. 

N

OTE

:

  The Model 707-001-EX-F07045 conduit or cable entries contain metric threads. 

Installation 

This enclosure must be installed by trained, qualified and 
competent personnel.  Installation must comply with state and 
national regulations, as well as safety practices for this type of 
equipment. 

CAUTION

  Do not install this equipment in 

hazardous areas other than those indicated on the approval 
listing in the Specifications section of this manual.  Such 
installation may cause a safety hazard and consequent injury 
or property damage. 

The mounting location must be flat and provide proper 
clearance, rigidity and strength to support the enclosure and all 
contained devices.  The enclosure is equipped with factory-
installed hinges.  The enclosure should be mounted with hinges 
on the left. 

 

Figure 1.  Model 707-001-EX-F07045 

Summary of Contents for 707-001-EX













Reviews: