background image

Titan Illuminated Crossing Telephone

11

4  Approvals

This mark indicates compliance with the
European R&TTE Directive 1999/5/EC

The telephone is suitable for inductively
coupling to Hearing Aids having a `T'
switch position in accordance with the
relevant Oftel Code of Practice. Use of
this facility for any other purpose than
that for which it was intended may cause
degradation in quality of a connection.

Degree of Protection: IP65

Declaration of Conformity

In accordance with European Directive 1999/5/EC (R&TTE)

GAI-Tronics Ltd., of Brunel Drive, Stretton business Park, Burton upon Trent, Staffordshire,
England, DE13 0BZ, 

declare

 under their sole responsibility that the following product is in

conformity with the standards listed below and hold the relevant technical documentation at
the above address.

Product Description

Titan Illuminated Crossing Telephone

EC Directives applicable

Notes

89/336/EEC

EMC Directive

73/23/EC

Low Voltage Directive

Standards applicable

Notes

BS6317
BS6305

Telephone Handset
Telephone Network Connection

EN 41003

Safety requirements for equipment to be connected to
telecommunications networks

EN50121-1
EN50121-4

Railway applications – Electromagnetic compatibility.
Emission and immunity of signalling and
telecommunications apparatus

Summary of Contents for Titan Illuminated Crossing Telephone















Reviews: