background image

 

4

 

Chapter 2 Precautions of Operation 

 

2-1 Attention 

 

Please carefully read the manual before installing and operating this device. 

Due  to  the  complex  nature  of  this  equipment  it  is  necessary  to  read  the  entire 

manual before installation. 

Never dismantle the equipment by any unauthorized personnel, or equipment may 

be damaged. 

This  manual  is  for  reference  only.  Pleases  consult  your  distributor  for  further 

assistance. 

The equipment has been strictly tested for quality before delivery from our plant. 

However,  this  equipment  must  not  be  used  in  dangerous  situations  or  where 

damage may result. 

After operation, shut off main power to the crane, power to receiver, and remove 

transmitter key. 

Transmitter  should  be  placed  in  a  safe  area  when  not  in  use  to  avoid  accidental 

pressing of buttons. 

The crane should be equipped with main power relay, limit switch and other safety 

devices. 

Don’t use equipment during lightening or high electrical interference conditions. 

Make sure that the batteries are in good condition and power for receiver is correct. 

Maintenance should only be done while the crane’s main power is off to prevent 

electrical shock. 

The contents of this manual may be amended by the manufacturer without notice. 

The  manufacturer  may  introduce  new  functions  to  the  equipment  as  necessary, 

therefore, the descriptions may change. 

 

 

Summary of Contents for SAGA1-K Series


















Reviews: