background image

10 

Malvern manual  version 1.0                                                                                                                                                    S.D  25.4.2014 

 

Intended use Fixed seat system.  

Supplied without the transfer trolley the seat is permanently fitted to the bath. All operation remains the same.  

A safety lap belt is supplied for added security whilst the user is seated on the chair and during bathing.   

It is the responsibility of the user/carer to ensure the lap belt is fitted while the product is in use.  

Check the temperature before use.  

 

To operate the shower open the valve marked “shower” and 
depress the handset.  

This is a hair wash/rinse system only. This is pre set to 38°C.  
After use turn off the valve, depress the handset briefly to 
empty any water still inside the hose and then place the      
handset back into it’s mount.  

 

 

 

User safety notes 

To reduce the risk of injury do not permit children or persons with infirmities to use this product unless they are 
closely supervised at all times.  

To avoid injury, exercise care when entering or exciting the Malvern bath.  

Never drop or insert any objects into any openings. 

 

Do not permit electrical appliances (such as hair dryer, lamp, telephone, radio or television ) within 152cm (60”) 
of this product.  

 

Avoid the abuse of alcohol, drugs or medication whilst using the Malvern bath. 

Warning! Please ensure that hands and objects are kept away from the underside of the seat when lowering 
onto the trolley & into the bath. 

Ensure all items for bathing including towels, face cloths, soap , shampoo etc. are within easy reach when using 
the bath.  

 

Summary of Contents for MALVERN













Reviews: