GAL A X Y AUDIO
Quick Start Guide
Included Components
1.
DHXR4 x1
3.
Rack Ears x2
4.
1/4" to 1/4" Audio Cable x1
2.
Antennas x2
1.
2
3
4
5
Setup
1
Attach the rack ears using the provided
screws.
Rack Mounting
(Optional)
1
Attach the BNC feed-through connectors
to the rack ears.
2
Attach the short BNC cables to the rear
panel antenna jacks, and to the BNC
feed-through connectors on the back of
the rack ears.
3
1
5
Follow steps 2, 3 and 4 of “
Operation
”
for each channel. Use the same group,
but a different channel for each.
Ex: Group 1; Channels 1, 2, 3 and 4.
10.
2.
3.
5.
7.
4.
6.
8.
Optional Accessories
5.
Power Supply x1
7.
BNC Cables x2
8.
Screws x6
6.
BNC Connectors x2
9.
Antenna Plugs x2
1.
HH65SC Handheld Mic
3.
MBP77 Body Pack
4.
LV-U3BK Lav Mic
2.
HH65 Handheld Mic
5.
AS-GTR Guitar Cable
7.
SM-W77 Shockmount Base
6.
HS-U3BK Headset Mic
1.
2.
3.
4.
7.
Insert the 5.5mm plug into the DC input
jack, plug the wall wart into a 120VAC
outlet.
Attach the antennas to the antenna jacks
1
Operation
Power on the receiver
1
Front Mount Antenna
(Optional)
Combined Outputs XLR Connect one
end of a shielded microphone cable to
the mix XLRM output, connect the other
end into your system input.
Combined Outputs: 1/4" Connect one
end of a shielded 1/4"M to 1/4"M cable
to the 1/4" Mix output, connect the other
end into your system input.
Individual Outputs: Connect a shielded
microphone cable to each channel’s
XLRM output needed, connect the other
end into your mixer input.
5.
10.
Quick Start Guide x1
9.
6.
1.
Rack Screws 10/32 x .75",
Phillips Truss Head Screws
2.
#2 Phillips Head
Screwdriver
What May be Needed
to Rack
(Not Included)
1.
2.
2
Press the "SET" button twice, the group
number will flash, use the up and down
buttons to select a group.
3
Press set again, the channel number will
flash, use the up down buttons to select
a channel.
4
With the transmitter turned on, place the
transmitter with it’s IR window (
figure 4a
)
facing the receiver IR window (
figure 4b
),
about 6" away. Press the ADS button on
channel 1. This will sync the Transmitter
to the Receiver.
4a
4b
GAL A X Y AUDIO
Q
uick Start Guide
Included Components
1.
DHXR4 x1
3.
Rack Ears x2
4.
1/4" to 1/4" Audio Cable x1
2.
Antennas x2
1.
2
3
4
5
Setup
1
Attach the rack ears using the provided
screws.
Rack Mounting
(Optional)
1
Attach the BNC feed-through connectors
to the rack ears.
2
Attach the short BNC cables to the rear
panel antenna jacks, and to the BNC
feed-through connectors on the back of
the rack ears.
3
1
5
Follow steps 2, 3 and 4 of “
Operation
”
for each channel. Use the same group,
but a different channel for each.
Ex: Group 1; Channels 1, 2, 3 and 4.
10.
2.
3.
5.
7.
4.
6.
8.
Optional Accessories
5.
Power Supply x1
7.
BNC Cables x2
8.
Screws x6
6.
BNC Connectors x2
9.
Antenna Plugs x2
1.
HH65SC Handheld Mic
3.
MBP77 Body Pack
4.
LV-U3BK Lav Mic
2.
HH65 Handheld Mic
5.
AS-GTR Guitar Cable
7.
SM-W77 Shockmount Base
6.
HS-U3BK Headset Mic
1.
2.
3.
4.
7.
Insert the 5.5mm plug into the DC input
jack, plug the wall wart into a 120VAC
outlet.
Attach the antennas to the antenna jacks
1
Operation
Power on the receiver
1
Front Mount Antenna
(Optional)
Combined Outputs XLR Connect one
end of a shielded microphone cable to
the mix XLRM output, connect the other
end into your system input.
Combined Outputs: 1/4" Connect one
end of a shielded 1/4"M to 1/4"M cable
to the 1/4" Mix output, connect the other
end into your system input.
Individual Outputs: Connect a shielded
microphone cable to each channel’s
XLRM output, connect the other end into
your mixer input.
5.
10.
Quick Start Guide x1
9.
6.
1.
Rack Screws 10/32 x .75",
Phillips Truss Head Screws
2.
#2 Phillips Head
Screwdriver
What May be Needed
to Rack
(Not Included)
1.
2.
2
Press the "SET" button twice, the group
number will flash, use the up and down
buttons to select a group.
3
Press set again, the channel number will
flash, use the up down buttons to select
a channel.
4
With the transmitter turned on, place the
transmitter with it’s IR window (
figure 4a
)
facing the receiver IR window (
figure 4b
),
about 6" away. Press the ADS button on
channel 1.
4a
4b
Attach the Antenna to the front end of
the BNC Connectors.
