OWNER’S MANUAL
BATTERY REPLACEMENT
1. Loosen the screw on the pedal to
open it.
2. Remove the battery from the
battery compartment and
disconnect the battery cable.
3. Connect a new battery to the
battery cable and put it back
in the battery compartment.
Make sure that the polarity
of the battery is correct and the
battery cable does not interfere with
the spring or pedal cover.
4. Push the coil spring into the spring
base and close the pedal.
5. Insert the thumb screw into the guide bush hole and firmly tighten the
screw.
IMPORTANT NOTES
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Do not use this apparatus near water.
5. Clean only with dry cloth.
6. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
7. Do not install near any heat sources such as radiators, heat registers,
stoves or any other apparatus (including amplifiers) that create heat.
8. WARNING: to reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture.
9. Protect the power cord from being walked on or being pinched.
10. Unplug this apparatus when unused for long periods of time.
11. There are no user serviceable parts inside. All servicing has to be done by
qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as when the power supply cord or plug
is damaged, when liquid has been spilled or objects have fallen into the
apparatus, when the apparatus has been exposed to rain or moisture, when
the apparatus does not operate normally or when it has been dropped.
PANEL DESCRIPTION
1. AC Adaptor Jack: Connect an AC adaptor (100-140V/50-60Hz).
An AC adaptor allows long and secure operation without worrying about
battery life.
Use the proper supply for your area’s Mains line voltage.
2. Indicator LED: This LED indicates when the effect is turned on.
• Operating on battery power only: when the LED becomes dim or does
not light the battery needs to be replaced.
INSTRUCTIONS
Thanks for purchasing our product. In order to make the best use of your
CE-100, please read the following carefully.
FEATURES
The CE-100 features 2-band filters for creating various chorus effects, which
offer a wide range of frequencies for effect applying. Obtain a natural chorus by
cutting low frequencies. Create a deep chorus by using the dual output jacks.
3. E. Level Knob: Use this control to adjust the output level of the effect
sound. Turn this knob clockwise to increase the volume of the effect sound
and counter-clockwise to decrease the volume of the effect sound.
4. Low Filter Knob: Use this control to adjust the bass frequencies of the
chorus sound.
5. High Filter Knob: Use this control to adjust the treble frequencies of the
chorus sound.
6. Rate Knob: Use this control to adjust the speed of the effect sound.
7. Depth Knob: Use this control to adjust the depth of the chorus effect.
Clockwise rotation deepens the effect.
8. Output Jacks A/B: Use the jacks to connect an amplifier or other units.
Use Jack A for mono output.
9. Pedal: Press the pedal to turn the effect on and off.
10. Thumb Screw: Loosen the screw to open the pedal for battery replacement.
(For details of the battery replacement, see “BATTERY REPLACEMENT”)
11. Input Jack: Connect your instrument to this jack. To prolong battery life,
disconnect all cables from the pedal when it’s not in use.
SPECIFICATIONS
Input Impedance 1MΩ
Output impedance 1kΩ
Recommended Load
Impedance
10kΩ or greater
Residual Noise
-93dBu (IHF-A, Typ.) (Filter Control knob in the center
position)
Power Supply
DC 9V; Dry Battery (6F22/9V), AC adaptor
Connections
Input, Output A (Mono) / B,
AC Adaptor
Controls
Pedal Switch, Effect Level,
Rate, Depth, Filter
Indicator
Check indicator (serves also
as battery check indicator)
Current draw
28mA, (DC 9V)
Dimensions
72*128*60 mm.
Weight
412g (no battery)
Option
AC adaptor
CE-100 CHORUS ENSEMBLE
CONNECTIONS
1. Connecting an instrument to this jack will automatically switch the unit on.
Be sure to disconnect the cord from this jack when the unit is not being
used.
2. Before connecting or disconnecting any instrument, make sure that the
volume of the amplifier is turned down.
3. For monaural output, use Output Jack A. Both the dry and the processed
signal are output.
4. For stereo use:
Output A: only the processed
signal is output.
Output B: only the dry
(unprocessed) signal is
output.
5. When you use a high output
guitar, the sound may be
distorted. If distortion occurs,
turn down the volume of the
guitar or use a limiter.
