background image

14

Foundation Requirements 

Concrete Foundation 

A new Galaxy spa pool can weigh over 
two tonnes once full so it needs to sit on a 
level surface that supports the entire base. 
We recommend a cured concrete pad with a 
minimum thickness of 100mm that is a little 
larger than the dimensions of your spa. 

 

Decking 

Decks are a common place to put a spa pool. 
If placing a spa pool on a deck, the deck load 
rating should be checked by an engineer or 
builder prior to placing a spa pool. To deck 
around a spa (or in ground it), please leave 
a minimum of 500mm around each side so 
there is easy access for a technician to service 
all the key components. Any in ground spa 
will need to comply with your local council’s 
fencing regulations.

Heat Pump Foundation

The installation of a heat pump unit will need 
a well supported flat surface for this to sit on, 
ensuring it meets the airspace requirements 
(page 23). Heat pumps weigh up to 45kg, 
so we recommend a concrete foundation for 
this as well. 

Spa Steps

Steps also need a flat, level foundation to 
sit on. Steps do need to remain moveable, 
so do not fix these in place.

2-Tier Steps

Length: 600mm 
Width: 580mm
Height: 300mm

Drainage 

Water splashing over the side of a spa pool is 
very common. Children moving around or a 
spa full of people are all part of having a spa!
Drainage needs to be considered to prevent 
water from pooling around the base as flooding 
issues are not covered under warranty.
A great way to ensure this is to incorporate 
drainage channels into your foundation to 
direct water away from the Spa Pool.
Drainage also comes into play when you 
change your spa’s water. You will need to do 
this every 3–4 months or in accordance with 
your water treatment plan. 
A hose attachment comes with your spa and it 
may be a good idea to have a dedicated piece 
of hose long enough to reach to your waste 
water or garden area. 
If you’re draining the water onto your grass or 
garden area, remember to let the temperature 
drop first. 
If you don’t have an adequate drain off area you 
may want to consider building drainage into your 
concrete foundation during construction. 

Summary of Contents for Rosa





























Reviews: