background image

 

2.2  Unpacking and Organizing the Components 

 

2.2.1 

Unpacking 

“Top off” the Battery Charge: 

Immediately after unpacking Box #3, top off the battery charge.  Your battery 

shipped in a fully charged state.  Strictly speaking, this will not be necessary. 

North America

:  Plug the female end of a standard (2 prong) extension cord into 

the battery and the other end into a 115 VAC outlet.  Follow the instructions in 

the charger’s manual and use the lowest charging rate available (always a good 

idea with any battery. 

Unpacking Hints - North America (cartons): 

This section to be completed later. 

Unpacking Hints - Overseas (crate/cartons): 

This section to be completed later. 

 

2.2.2 

Organize the Components According to the Assembly Steps 

The major components (base, platter, motor pod) are wrapped in plastic stretch 

wrap to protect their finish from fine scratches during transport.   

We advise leaving this stretch wrap in place on the turntable base until after you 

have installed the brass bearing housing and have attached the ground wire to 

the underside of the bearing.   

This last operation requires turning the turntable base upside down. 

 

Assembly 

Step 

Part 

Box # 

Inner Box 

Platter 

Platter 

n/a 

Base / Bearing 

  Turntable Base 

  Tip toes 

n/a 

Base / Bearing 

  Bearing 

  Ground wire 

8” x 4” x 4” 

Base / Bearing 

  Strap Wrench 

  Bearing oil 

n/a 

Motor Drive 

  Motor Pod 

  Umbilical Cord 

  Tip Toes 

9” x 9” x 6” 

Summary of Contents for Serac

























Reviews: