background image

    

 

 

 
 
 

TEL:

 

+44 (0) 121 608 4433

 

FAX:

 

+44 (0) 121 608 4477

 

 

www.

galsys

.co.uk

 

galleonsupport

.com

 

 

SIGNALCLOCK V2 Manual

 

If your network does not have a PoE enabled network switch, you will need to use a power 
injector with the clock. A power injector passes Ethernet communications through while also 
injecting power in accordance with the IEEE 802.3af standard. 

 

The above diagram shows how a power injector fits into the set up. If you have a power injector 
supplied by Galleon, connect the h

ub/switch to the port labelled “LAN” on the 

power injector and 

connect the clock to the port labelled “PoE” on the 

power injector. Plug the power supply in and 

wait for the 

clock’s display to come on. W

hen the unit powers up, make a note of the IP address, 

as this will be needed to configure the unit via the web interface. 

2.

 

DHCP SERVER 

By default, the SignalClock is set to use DHCP to obtain its IP Address. If the clock is unable to 
receive network settings from the DHCP server, the clock will cycle: 

----

‘.

 If the clock is unable to 

obtain an IP address after several attempts, it will set its IP address to 169.254.0.1. This is done so 
that the unit can be configured without requiring a DHCP server. 

Once the unit has obtained an IP address from a DHCP server on your network, configuration (such 
as static network settings) can be applied to the clock. For help with this, please see the 

Web 

Configuration

 section of this manual. 

 

Summary of Contents for SignalClock Series




















Reviews: