background image

We are very proud of the 1000RB, G-K's most pow-
erful bass amplifier to date, and in many ways, the
culmination of 27 years in the amplification busi-
ness.  The 1000RB was designed with you in mind -
to be your personal creative tool, to give you the ulti-
mate bass response and tone.  We've learned many
things by talking to bass players like you for almost
three decades.  We know you want lots of headroom
and raw power, yet you want your amp to be dead
quiet and free of noise.  Your need fast response and
clarity.  And perhaps most of all, you want all that
great performance night after night, year after year,
from an amp that will never let you down.  

The 1000RB is definitely not just another high power
bass amp.  Its High Current Capacity output stages-
capable of delivering instantaneous power of 5,000
watts - are revolutionary. Its relay-activated Fault
Detection Circuitry is state - of - the art.  All the
design parameters for the 1000RB are optimized for
response, headroom, and reliability.
Like all G-K bass amps, the 1000RB is user friendly.
It's easy to get the sound you're looking for - in fact,
it is hard to get a bad sound.  We took all the same
responsive bass tone G-K amps are known for, and
made it even better.  We think you will be very
pleased with your new 1000RB.  We are.

Bob Gallien & Rich Krueger

Introduction

Power

: 500 watts RMS into 4 ohms

High Current Capacity

:  60 amps peak current 

(5,000 watts of instantaneous power) gives the 
1000RB unparalleled transient response with 
complete control over the movement of your 
speakers.

Low Noise Operation

: Both preamp and power 

amp stages have increased headroom so that 
noise ( hiss ) is barely perceptible.

Fault Detection Circuitry

: Relays automatically 

disconnect the amplifier from your speakers 
during power up/down, or if any unsafe 
operating conditions occur.

Fan Cooling

: Temperature controlled, continuously 

variable fan speed.

Tuner output with footswitchable mute.

Tunable Voicing Filters

Four Band Active Equalization

Boost 1 (Normal) & Boost 2 (High Gain)

Footswitching between these two sections.

GIVE Technology

: Gate Induced Valve Effect, 

used throughout for warm, "punchy" response.

Parallel effects loop with Stereo Aux In and Aux 

Return Level

Direct/balanced output

: Electronically balanced, 

low impedance output with variable level, 
pre/post & ground lift switches.

Speakon

connectors

: For reliable connection of 

high power / high current outputs to speaker 
cabinets.

1000RB Features

3

Summary of Contents for 1000RB









Reviews: