background image

SYMPTOM

POSSIBLE CAUSE

POSSIBLE SOLUTION

NO LIGHTS

UNIT NOT PLUGGED IN

CONNECT POWER CORD TO AC OUTLET, 

CHECK AC OUTLET

UNIT HAS FAILED

REFER TO SERVICE TECHNICIAN

POWER LED ON BUT

SHORTED SPEAKER CORD

REPLACE W/DIFFERENT CABLE

FAULT LED ALSO ON

SPEAKER IMPEDANCE TOO LOW

CHECK MANUAL FOR RECOMMENDED 

SPEAKER LOADS

AMP HAS OVERHEATED

TURN AMP OFF, WAIT&TURN ON 

CHECK SPEAKER IMPEDANCES

AMP HAS FAILED

REFER TO SERVICE TECHNICIAN

POWER LED ON BUT

TUNING MUTE ON

TURN TUNING MUTE OFF

NO SOUND

EFFECT IN LOOP TURNED OFF

TURN EFFECT ON

VOLUME, BOOST,MASTERS OFF

TURN CONTROLS UP

INSTRUMENT TURNED OFF

TURN INSTRUMENT VOLUME UP

BAD GUITAR CABLE

REPLACE CABLE

BAD BATTERY IN ACTIVE BASS

CHECK BATTERY

COMPONENT FAILURE

REFER TO SERVICE TECHNICIAN

HUM AND/OR NOISE

PICKUPS TOO CLOSE TO AMP OR

TRY MOVING,TURN OFF LIGHTS,

OR OTHER ELECTRICAL DEVICE

OR OTHER ELECTRONIC DEVICES

BAD GUITAR CABLE

REPLACE CABLE

COMPONENT FAILURE

REFER TO SERVICE TECHNICIAN

DISTORTION

INPUT STAGE CLIPPING

PRESS-10Db SWITCH, TURN

DOWN BASS

PREAMP CLIPPING

TURN DOWN VOLUME, ADJUST EQ

EFFECTS CLIPPING

TURN DOWN VOLUME, BOOST OR 

LEVELS ON EFFECTS

POWER AMP CLIPPING

TURN DOWN VOLUME, BOOST OR MASTER VOLUME

BAD BATTER IN ACTIVE BASS

CHECK BATTERY

COMPONENT FAILURE

REFER TO SERVICE TECHNICIAN

LOUDNESS IS

EFFECTS NOT HOOKED UP

CHECK MANUAL FOR USING

BELOW NORMAL

CORRECTLY

EFFECTS

WRONG SPEAKON CABLE

USE NORMAL SPEAKON CABLE,

NOT BRIDGE MODE CABLE

HUM IN DIRECT OUT

GROUND LOOP

PRESS GROUND LIFT SWITCH

DISTORTION IN DIRECT

SIGNAL TOO "HOT"

TURN DOWN BAL.LEVEL CONTROL

TUNING MUTE

BAD CORD FOR RF2 FOOTSWITCH

REPLACE CORD

AND/OR BOOST2

RF2 DEFECTIVE

REFER TO SERVICE TECHNICIAN

NOT WORKING

COMPONENT FAILURE

REFER TO SERVICE TECHNICIAN

Troubleshooting

GALLIEN-KRUEGER • 2240 PARAGON DR. • SAN JOSE, CA 95131
US: (408) 441-7970 • FAX (408) 441-8085
EUROPE: 41.42.234520 • FAX: 41.42.239525

7

Summary of Contents for 1000RB









Reviews: