© Copyright
Gallo Technologies
. All Right Reserved
- 13 -
Rev. V8.2- 20212
2 Pin Wire Harness (
Control Module Power, Parking lights)
C4: RED 15 Amp fused wire
–
+ 12v Constant Battery Input (Control Module Supply Power)
. This connection
should have co12v available (
BAT
terminal on ignition switch or equivalent). Solder connect the RED wire.
C4: YELLOW – Parking Light +12v output 10 Amps fused.
Solder connect one of the YELLOW wires to the
vehicle’s parking lights. If parking lights require more than 5 amps (not normal) use an external 30 Amp relay.
7 Pin Wire Harness
(Trunk Release, Door Trigger Circuit, Foot Brake
Switch, Siren and System Ground).
C5: GREEN/RED – Window Close Output Neg. (-).
Connect the GREEN/RED wire to a window close module (not
included) Neg. (-) input. Follow the window close module instructions for wiring to window motors. Do not connect
this wire directly to the vehicle’s window close switch.
C5: PURPLE – Trunk Release Output Neg. (-).
Connect the PURPLE wire to the trunk release Neg. (-) trigger wire
on the vehicle’s trunk release relay. In the event that a trunk release is to be added to the vehicle, an additional relay
and trunk release solenoid will be required.
C5:BLACK/YELLOW –Triggered Alarm Output (-).
Use this output to turn on any device that may be used to
identify when the alarm has been triggered. i.e. additional horns, lights, etc. that will turn ON only when the alarm is
triggered. An additional relay may be required if the current load exceeds 150MA.
C5: BLACK/WHITE – Neg. (-) Door Trigger switch Input.
Connect the BLACK/WHITE wire to the Neg. (-) Door
Trigger switch. If the vehicle has “+” Pos Door Trigger input use the BLUE wire from connector
C7
.
C5: PINK - (+12v) Foot Brake Switch Input Used for door lock and Starter enable input.
Connect to Foot brake
switch terminal that has +12v only when foot brake is depressed.
C5: ORANGE: - Siren +12v Output.
Connect to the RED Siren wire. Connect the second siren input (BLACK wire)
to a good chassis ground. If the vehicle’s horn is used connect the ORANGE wire to the (+) on the horn relay.
C5: BLACK – Neg. (-) Ground Connection.
Connect the BLACK wire to a good chassis ground in a convenient
location.
3 PIN Wire Harness
(“Push Start Stop” Button)
The
“PUSH START STOP”
button can be surface mounted in a convenient location on the dash or can be mounted
using the supplied adjustable bracket for mounting under the dash or on the console. The high strength double stick
adhesive disk is to be used on the back side of the switch with both mounting methods. Make certain that the back
of the button and the mounting surface is thoroughly cleaned with
isopropyl alcohol
to remove any dirt, grease or
vinyl dressing materials.
DO NOT use acetone, MEK, lacquer thinner or any other harsh chemicals as they will
destroy paint, vinyl and plastic
. The adhesive will not come loose or degrade as long as the surface has been
cleaned thoroughly. Attach the adhesive disk to the back of the button first.
If you choose to mount the button on the dash with the wire hidden behind the button then drill a 3/8” dia. hole in a
location where the small wire and connector can be fed through the dash. Rout the
“PUSH START STOP”
button
wire to the module. Connect the White 3 terminal connector to the module. The connector is indexed so that it can
only be installed in one direction.
4 Pin Wire Harness ( Start enable & Disarm Output)
C7: BLUE – Pos. (+) Door Switch Input.
Connect the BLUE wire to a Pos. (+) Door Trigger switch. If the vehicle
has “-” Neg. Door Trigger input use the BLACK/WHITE wire from connector
C5
.
C7: YELLOW – Start Enable Input.
For
Automatic Transmission:
Connect the YELLOW wire to a good chassis ground (-).
Installing Connector C4:
Installing Connector C5:
Installing Connector C6:
Installing Connector C7:
