background image

© Copyright

Gallo Technologies

. All Right Reserved

- 4 -

Rev. V8.2- 20212

M

ute Button: Silent-(Arm/Disarm)/Remote-Lock/Siren-Stop

a.)

Silent Arm:

When in

disarmed

mode press

one time, parking lights flash once, Blue L.E.D. on the Engine Start

button will flash slowly, the siren will not chirp, the doors will lock and system will be in

armed

mode. If a

door is not closed when pushing the

button, the siren will chirp and the parking lights will flash 3

times and the system will stay in the

armed

mode. When the door is closed the system will be in the

armed

mode. (See “Functions Options” Table 1).

Shock Sensor will become active after 15 sec.

Siren stop: When the alarm siren is triggered, pressing the

button or the

button will stop the siren

sounding and the system will stay in the

armed

mode. Pressing the

button will disarm the system

and unlock the doors.

b.)

Silent Disarm:

When in the Silent Armed mode, press

one time will unlock the doors and the parking lights will flash

twice.

S

iren Button: Auto Door Lock/Unlock/Car-Locating/Anti-hijack

a.) Auto Door Lock/Unlock enable or disable:

When the system is in the disarmed mode, pressing and holding

for 2 sec will enable or disable the

RFID auto door lock/unlock function. (parking lights flash 1 time when disabled or parking lights will flash
3 times when enabled )

While driving, pressing the

button will only lock the doors.

If the alarm has been triggered, pressing the

button will stop the siren. The system will remain in the

armed mode

.

b.) Car Locating:

When the system is

armed

, holding this button for more than 2 seconds, the siren will chirp and the

parking lights will flash five times.

c.) Anti-Hijack

:

When the engine is running, holding the

button for over 2 seconds, the parking lights will flash

twice and Anti-Hijack mode will be started.

After 40 seconds, the system will enter armed mode, siren will chirp (non-continuous) for 20 seconds. For
another 60 seconds, the parking lights will flash and

the Engine will turn OFF

. At this time the system

will stay armed.

Pressing the

button or the valet will release the triggered Anti-Hijack mode to the disarmed mode, but

will not turn off the anti Hi-jack function.

NOTE: The Anti Hi-Jack function can be turned OFF (disabled) by resetting the Anti Hi-jacking
programming option in Table 1 “Function Option Chart”.

In the OFF setting, Anti Hi-jacking

can note be invoked.

d.) Light / Heavy Shock Sensor Programming

Within 3 sec after Arming, press the

button to program light / heavy shock sensor sensitivity.

No. of times to press

button

Function

Description

Remark

1

OFF light shock

Park lights flash 1 time
Siren chirps 1 time

Siren does not chirp if in
Silent Arm mode

2

OFF light/heavy shock

Park lights flash 2 times
Siren chirps 2 times

3

ON light/heavy shock

Park lights flash 3 times
Siren chirps 3 times

4

ON light shock

Park lights flash 4 times
Siren chirps 4 times

If the

button is not pressed within 3 sec of entering the armed mode the program will

automatically enter the light/heavy shock mode.

Summary of Contents for GTStarter-2 GTS-2
















Reviews: