IF630 Programming 5/26/01
___________________________________________________________________________________________
Rev 3.0
83
Change Baud
The Change Baud selection will cause the system to output a printer test pattern to the RS-
232 port. This continuous output allows the user to select the baud rate of the connected
device without having to cause system abnormalities.
Change Menu 1
1=Pass 2=Code 3=Date 4=Seq
5=Baud 0=Exit
>5
Ready To Read Dip Switch and Set
Serial Port 1's Baud Rate.
Press Enter Key To Proceed...
0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdef
ghijklmnopqrstuvwxyz{|}~!"#$%&'()*+,./0123456789:;<=>?@ABCDEFGH
IJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~!"#$%
&'()*+,./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^
_`abcdefghijklmnopqrstuvwxyz{|}~!"#$%&'()*+,./0123456789:;<=>?@AB
CDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|
}~!"#$%&'()*+,./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUV
WXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~!"#$%&'()*+,./0123456789:;
<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqr
stuvwxyz{|}~!"#$%&'()*+,./0123456789:;<=>?@ABCDEFGHIJKLMNOP
QRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~!"#$%&'()*+,-
./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ{|}~
Baud Rate Switch
Settings
The baud rate is changed by setting DIP switch SW1 on the CPU module to the
desired speed ( see below table). Select this option to read new setting.
SW1 - Settings
S1
Open
Do Not Change
S2
Open
Do Not Change
S3
Always Closed
Do Not Change
S4
Open
Do Not Change
S5
Open
Do Not Change
S6
Open
Do Not Change
Note
:
P2 baud rate of is selected via S7 and S8.
Auto Detect
Baud rate is utilized for peripheral devices.
S7, S8 Open
9600 Baud Rate
S7, S8 Closed
4800 Baud Rate
S7 Open, S8 Closed
2400 Baud Rate
S7 Closed, S8 Open
1200 Baud Rate
Summary of Contents for Smart Start IDENTIFLEX 630
