6
CONTROL PANEL FUNCTIONS
AND FEATURES
Single Digit (1-9)
Memory LED Display
Three Digit (XX.X)
Tension Setting Display
or String Length LED
Display
String Length Meter Button
- feature is
currently not available.
Lbs/Kgs Button
- Changes tension
display from Lbs to Kgs. Each press
of the button toggles back and forth
between Lbs and Kgs.
Speed Button
- Changes pulling speed
of winder from Fast (default) to Medium
to Slow. Slow speed is recommended
for low stretch strings, such as Kevlar.
Each press of the button toggles be-
tween Fast, Medium and Slow speeds.
Pre-Stretch Function
- Pulls string 10%
or 20% over the tension setting (up to 90
lbs / 40.8 kgs), releases the string, and
repulls to the tension setting. Each press
of the button toggles between 10%, 20%
or no pre-stretch.
Clear Button
- Clears display to enter
a new tension or to reset String Length
Meter measurement.
Knot Function
- Increases pulling ten-
sion by 10% over the setting value (max
90 lbs / 40.8 kgs) for one pull. During the
pull the LED stays lit to indicate the Knot
function is enabled.
Tension Index Buttons
- Changes
tension setting in +/- 1.0 or +/- 0.1 Lb or
Kg increments. Holding the button down
will scroll the tension setting values up
or down. Tension settings entered with
the tension index buttons are placed into
temporary memory setting “0”.
Memory Button
- Indexes from 9 preset
tension settings that can be stored in
memory. Settings are retained even if
machine is turned off. Each press of
the button indexes to the next memory
setting. Memory settings 1-9 must be
entered using the keypad followed by
pressing the “ENT” button.
Enter Button
- Saves displayed tension
for Memory setting - when tension is en-
tered using the keypad display
fl
ashes
until this button is pressed to save the
setting. Also Clears display for String
Length Meter measurements.
Test Button & Racquet Strung -
Press once for approximate number of
racquets strung. Press again to return.
Press and hold for 5 seconds and the
machine does an internal diagnostic
check, such as the one performed at
start-up.
15
Adjusting the String Clamp Jaw
Spacing
The string clamps will need minor adjust-
ments according to what string type, con-
struction, and gauge you are using.
To adjust the gap (clamping pressure)
between the clamp jaws, insert the string
through the racquet as if you were begin-
ning the main strings. Clamp the strings
and pull tension. If the string slips through
the jaws of the clamp, tighten the clamp
by squeezing the clamp jaws together by
hand while turning the Adjustment Knob, in
the clockwise direction. If the clamp leaves
impressions or damages the string, it may be excessively tight and should be adjusted by
turning the Adjustment Knob counter clockwise to open the gap between the jaws. The clamp
jaws should be cleaned periodically to be free from dirt, oil, and any string coating residue
to grip properly. Knife sharpening stones are excellent for removing build-up on the diamond
coated surfaces and are available.
Adjustment
Knob
MAINTENANCE & ADJUSTMENTS
Clamp Base Locking Nut Adjustment
In the event the Locking Lever rotation is
insuf
fi
cient to ensure smooth operation of the
clamp base, very minor adjustments to the
Clamp Base Locking Nut can be made with
the supplied 17mm socket. Tighten or loosen
the locking nut in very small increments to
provide more clamping pressure or running
clearance as needed.
Quick Action Clamp Base Removal
Quick Action clamp bases can be removed
from the turntable for maintenance or clean-
ing by removing clamp stop located at the
end of the slot in the turntable. To remove the
clamp stop, remove the two screws holding
the clamp stop in place from the underside of
the turntable. Lift the clamp stop out of the
slot, slide the clamp base to the end of the
slot and lift it out. Replace the clamp base and
clamp stop in reverse order.
