34
35
www.Deuba24online.de
www.Deuba24online.de
•If you wish to use an extension cable, ensure
that the cable is suitable for the purpose and has
Otherwise this may
cause a loss of performance in the product and
unsure, contact a specialist.
extension cord suitable for outdoor use.
Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
•If you cannot avoid using an electrical tool in a
damp environment, ensure you use a residual
current device with a trigger current of 30 mA or
less.
Use of an RCD reduces the risk of electric
shock. NOTE: The term "residual current device
(RCD)" may be replaced by the term "ground
fault circuit interrupter (GFCI)" or "earth leakage
circuit breaker (ELCB)".
•Do not force the product.
Use the appropriate
power tool for the task in hand. The correct
rate for which it was designed.
•Do not use the power tool if the switch does
not turn it on and
off.
Any power tool that
cannot be controlled with the switch is danger-
ous and must be repaired.
•Disconnect the plug from the power source
product.
reduce
•Store power tools that are not in use out of the
reach of children.
Do not allow persons unfamiliar
Power tools are dangerous in the hands of untrained
users.
•
Maintain power tools.
Check for misalignment or
binding of moving parts, breakage of parts and any
before using the product. Many accidents are
caused by badly maintained power tools.
•Use the power tool, accessories and other tools
Take
be carried out.
•Use of the power tool for purposes for which it
was not intended may result in a hazardous
turning the product on.
result in personal injury.
•Avoid switching on accidentally.
Ensure that
the product is switched
off
before you connect it
to the power supply or carry it anywhere. When
carrying the product, having your
finger
on the
switch or the unit switched on and connected to
the power supply, may lead to accidents.
Safety notes for the shredder
•Check before switching on whether the blades
•Never use the product without the feed
hopper.
•If the product is blocked,
first
switch
off
the
device, disconnect the plug from the mains and
removing the blockage.
Keep the On / Off switch
clean and free from foreign objects.
•Before switching on, the product must have
•Check before switching on whether all screws,
onto material being cut while the blade is
Remove cut materials that are
switched off.
TRAINING
a) Become familiar with the user guide before
b)Never allow children or people unfamiliar with
c)The operator or user of the product is responsible
for accidents or hazards occurring to other people or
their property.
PREPARATION
c) Only operate the product in open space (e.g. not
close to a wall or a
fix
ed object) and on a
fi
rm, level
surface.
d) Do not operate the product on a paved or gravel
surface where ejected material could cause injury.
nuts, bolts, and other fasteners are properly secured
to an authorised service centre to replace damaged
or unreadable labels.
f) Before use, check the supply and e
x
tension cord for
signs of damage or aging. If the cord becomes
damaged during use, disconnect the cord from the
supply immediately. Do not touch the cord before
the cord is damaged or worn.
g)Do not operate the product in the vicinity of
bystanders, especially children and pets.
OPERATION
chamber to make certain that it is empty.
b) Keep your face and body away from the feed intake
opening.
c) Do not allow hands or any other part of the body or
clothing inside the feeding chamber, discharge chute,
or near any moving part.
and balance. Do not overreach. Never stand at a
higher level than the base of the product when
feeding material into it.
e) Always stand clear of the discharge zone when
f) When feeding material into the product be
cans or other foreign objects are not included.
or if the product should start making any unusual
product from its power supply, and take the following
steps:
i)inspect for damage;
ii) replace or repair damaged parts;
h) Do not allow processed material to build up in the
discharge chute as this may prevent proper discharge
or blockage and can result in kickback of material
through the feed intake opening.
i) If the product becomes clogged, switch the product
-
nect the product from its power supply before
clearing debris.
j) Never operate the product if the guards, covers,
not in place, and not in good working order.
k) If dust is created by the shredding process, wear a
suitable dust mask to prevent respiratory injury.
l) Do not move or transport the product while the
motor is running.
m) Switch
off
the product and disconnect from the
power supply whenever you leave work area.
