3
6
Chain guard
The chain guard must be clipped onto the chain and sword as soon as the sawing work
has been completed and whenever the chainsaw has to be transported.
Chain brake
In the event of kick-back, the chain brake (3) will be actuated via the front finger guard.
The front finger guard is pushed forwards by the back of the hand and this causes the
chain brake to stop the chain saw, or rather the motor, within 0.12 s (Fig 5, I).
Releasing the chain brake (Fig 5)
To be able to use your chain saw again, you must release the saw chain again. First
switch off the chainsaw. Then push the front finger guard (3) back into the vertical
position until it locks in place (Fig 5, H). The chain brake is now fully functional again
Sharpening the saw chain
You can have your saw chain sharpened fast and correctly by specialist dealers, from
whom you can also obtain chain sharpening equipment to enable you to sharpen the
chain yourself. Please follow the corresponding operating instructions. Take care of your
tools. Keep your tools sharp and clean to enable you to work well and safely. Follow the
maintenance regulations and the instructions for changing tools
Starting up
Always wear safety goggles, ear muffs, protective gloves and heavy-duty work clothes!
Use the saw only with approved extension cables with the prescribed insulation and
connections designed for outdoor use (approved rubber- sheathed cables) which
fit the chainsaw plug. The chain saw is equipped with a two-handed safety switch.
The chainsaw works only when one hand holds the front grip (2) and the other hand
actuates the switch on the rear grip (1) . If the chainsaw does not run, the chain brake
must be released at the front finger guard (3). Be sure to read the sections “Chain
brake” and “ Releasing the chain brake “ on this point. After switching on, the chainsaw
will run immediately at high speed . To switch off: Release either the ON/OFF switch (13)
on the rear grip or the other switch (2) on the rear grip. The release of ON/OFF switch
results the stop of the chainsaw within 2sec., and heavy sparkling. This is normal and
safe for the proper operation of the chainsaw. After working with the chainsaw, you
should always: Clean the saw chain and guide bar and replace the chain guard.
Chainsaw protection Never use the chainsaw in the rain or in damp conditions. If the
extension cable is damaged, pull the plug out of the power socket immediately. Never
work with a damaged cable. Check the chainsaw for damage. Before using your tool
again, check the safety devices or any slightly damaged parts to ensure that they are
in good working order. Make sure the moving parts are working correctly. All the parts
must be correctly assembled and meet all the conditions required to ensure that the
chainsaw works correctly. Any damaged safety devices and parts must be properly
repaired or replaced immediately by a Customer Service workshop, unless there are
instructions to the contrary in these operating instructions.
www.DeubaXXL.de
Summary of Contents for Deuba DBKS004
