If you feel confident that you do not need to read through these instructions, see page 2…. January 09
Feedback….
As we are forever trying to make sure you are our happiest customer, we are always on the look-
out for ways in which we could do better. Please fax us on
06 878 5758
or send us an email to
feedback@gardenmastersheds.co.nz with your thoughts. To help you we have listed a few aspects
that we would like you to comment on. You do not have to include your details, but if you do we
will forward you a
free
gift.
1.Finding out about our range of garden sheds and the various options we offer….
2.The store and the sales person that you purchased from….
3.The delivery and the overall dealings for the purchase of your shed….
4.The assembly of your shed and clarity of instructions….
5.Did the shed fit your needs? What will you order differently next time?
Well done you have finished the panels….
Points to note as you construct your shed:
Do not
attempt to assemble panels in windy conditions
Make
sure your foundations are squared and level before erecting panels.
It is
easier to remove all swarf (filings) before you stand your walls up
Complete
all
panels
before erecting your shed.
Keep a firm grip on panels when handling. If they slip they will cause damage.
Always wear non slip gloves protective footwear and eyewear
.
5: Now to join your corners and put your roof on….
1st: Stand up the back wall and as your helping hand is holding it up bring the Left end wall into meet it
at the left corner overlapping the corners as Fig
1
. Drill & Fix at approx 100mm down from the top
and up from the bottom drilling and fixing from the outside.
2nd: Bring the Right end wall into the right back corner and perform the same again checking to make
sure the walls are sitting flat at the bottom
3rd: Bring the front wall into place and join the front corners to the end walls same as the back.
4th: Finish joining corners by fixing at approx 300mm apart. You will find it easier to drill
these corners if they are supported on the inside. Use the handle end of a hammer
into the inside of the corner, but beware of drilling holes in the end of your hammer.
5th: With a person at each end of the roof, waft it over top of your upright walls and lower
down on top with an overhang that looks best to you. At the left end fix thru the “L”
flashing into the top channel of the left end wall. Measure the overhang at the back and
fix the right end “L” to the right end wall with the same overhang as the Left end. If the
roof is difficult to get to the same overhang at each end this will be caused by unlevel
site
or
walls are not square. Adjust accordingly. Fix “L”s at 300mm’s apart.
6th: Using your ladder and tape measure, fix down thru the top of the roof, thru the pan
into the top channel of front and back walls. (10mm more than the overhang). Fix be-
side every 2nd rib. (Fig 2). You will not need to worry about these fixings leaking as
any water seeping thru these fixings will end up on the outside of the walls.
7th: Attach padbolt to door strap and fit door braces if not already done so. Check that all
swarf is removed and most importantly….
8th: Fix your shed down to its foundations. If your foundations are unlevel or bowed, you
will have problems with your padbolt and door levels. This can be fixed by slipping a
spade under either door jamb and lifting. You will soon get a feel for which side needs propping up.
Well done!
It is
utmost
essential that every shed has
a floor, but the only way to make sure
your shed is there to stay on windy sites is
with a recessed concrete floor
and
phone
0800 80 SHED
for more free advise
.
If you choose to vary from these instructions your warranty will be impaired.
Pg 4
Recessed floor clamps
For especially poured floors
with recess around perimeter.
Flat floor clamps
For existing concrete only.
Water can seep underneath.
Fig
1
Fig
2
If you feel confident that you do not need to read through these instructions, see page 2…. January 09
GM1511
- Flat Roof Shed
1530mm Wide x 1080mm Deep x 1830mm H
ASSEMBLY INSTRUCTIONS
“
This shed has
1 Box
only
”
Quick Tips to keep in mind as I build my shed:
Try to remove swarf (drill filings) from panels as I assemble them.
My basic job is to cap the sheeting to make the panels. Drill & Fix.
All components are cut to length.
Do not
cut any parts unless instructed.
They are only a phone call away
0800 807 433
or email to info@gardenmastersheds.co.nz
Fixings thru the
inside
of the channels into the sheeting are just as
important
as the
outside.
What tools will I need?
Drill and drill bits - 3.3mm (1/8th”) for shed and 5mm (3/16th”) for padbolt
Screwdriver or Riveter. (Note: all colour sheds come with rivets only)
Tape measure for roof overhang.
Ladder for fixing down thru the top of the roof.
Tin snips for a small nik on top channel of gable end walls only. (If applicable)
Non slip gloves, good shoes, goggles, a helping set of hands and
no
gusty winds!
My basic
pa
rts list…..
(fo
r
st
an
dar
d
sh
ed
s)
P
leas
e c
hec
k
par
ts
c
ar
ef
ul
ly
an
d a
dv
is
e i
m
m
edi
ate
ly
if an
y d
am
age o
r
lo
ss
.
4 x 1830 mm Sheets and
2 x 1/2 sheets for
back & sides
2 x 1200mm long sheets
for the roof
Door pre-hinged to
715mm sheet with
door jamb
4 x 1065mm channels for End walls
2 x 1515mm channels for
the Roof
4 x 1515mm channels with ends cut
for Front & Back walls
2 x 1200mm “L”s for flashing the
roof to the side walls
2 x 793mm Door
spacers
Pg 1
1 x Pack of fixings with padbolt
Screws for Zincalume sheds
Rivets for Colour sheds
2 x “Z” Door braces
1 x 290mm wide sheet
with door jamb
attached
1 x “Z” door jamb attached to
a channel for the corner
door jamb
