EN
4
EN
4
INTENDED USE
The GARDENA Spreader L is intended to spread spreading material and
lawn seeds.
Do not use the product to spread chippings.
ASSEMBLY
To assemble the wheels and the foot [Fig. A ]:
1. Put the wheels
(1)
on the axles and push the hubcaps
(2)
on the axles
until it audibly engages (if necessary use a hammer).
2. Slide the foot
(3)
on the spreader and tighten the screws
(4)
.
To assemble the holms and the handle [Fig. B ]:
3. Slide the lower holm
(5)
into the spreader and tighten the screws
(6)
.
4. Slide the upper holm
(7)
into the lower holms
(5)
and tighten the screws
(6)
.
5. Slide the handle
(9)
on the upper holm
(7)
, put the screw
(8)
through the
hole in the upper holm
(7)
put the mother
(10)
on the screw
(8)
and tighten
the screw
(8)
.
To assemble the wire rope [Fig. C / D ]:
6. Route the wire rope
(11)
from above through the opening in the spreader.
7. Put the wire rope
(11)
into the holder
(12)
and pull the wire rope
(11)
until it
audibly engages.
8. Assemble the wire rope
(11)
into the clip
(13)
as shown in Fig. C.
9. Hook the clip
(13)
into the handle
(14)
so that the lower, half-width riders
are pushed onto the handle.
OPERATION
To adjust the spreading quantity [Fig. D ]:
Adjust the spreading quantity you require by referring to the dosage table
(see www.Gardena.en) on the scale
(14)
at the handle. Comply with the
instructions given by the spreading material manufacturer.
1. First pull the quantity adjustment clip
(13)
vertically upwards, slide the clip
to the desired position to the right or left and let the clip engage.
2. Fill in the spreading material.
Release the handle
(9)
during filling, interrupting the spreading process and
transport.
Note: Due to the different sizes of fertiliser and seeds, the infor-
mation on the dosage table is given for reference purposes
only. Always observe the safety instructions of the fertilizer manu-
facturer when applying an iron fertilizer.
To measure the spreading quantity [Fig. E ]:
A 1 m
2
smooth, dry and clean test area is required (e. g. garage).
1. Clean the test area (e.g. with a vacuum cleaner/broom).
2. Place the quantity adjustment clip
(13)
in position 4 and spread the
spreading material over a length of 2.15 m (corresponds to a 1 m
2
scattering area).
3. Sweep/vacuum up the spreading material, weigh it and compare it with
the recommended manufacturer specifications.
4. Repeat steps 1 to 3 with adjusted spreading adjustment
(13)
position until
the scattered spreading material quantity corresponds with the manu-
facturer specifications.
MAINTENANCE/STORAGE
[Fig. F ]: After use open the cylinder cover
(15)
and empty and clean
the spreader. If necessary, dispose of any spreading material residue
in accordance with local regulations.
SERVICE / WARRANTY
Service:
Please contact the address on the back page.
Warranty:
In the event of a warranty claim, no charge is levied to you for the services
provided.
GARDENA Manufacturing GmbH offers a two-year warranty (effective as of
the date of purchase) for this product. This warranty includes all significant
defects of the product that can be proved to be material or manufacturing
faults. This warranty is fulfilled by supplying a fully functional replacement
product or by repairing the faulty product sent to us free of charge; we
reserve the right to choose between these options.
Consumables:
The warranty does not cover non-repairable parts (e. g. fertiliser).
EN
4
EN
4
EN
4
EN
4
Та
ше
в
-
Га
лв
ин
г
ОО
Д
www.tashev-galving.com
