background image

 

 

WARRANTY 

ROTARY SCREW COMPRESSORS AND VACUUM PACKAGES 

OIL INJECTED – OIL FREE 

 

 

 

GENERAL PROVISIONS AND LIMITATIONS

 

Gardner Denver (the “Company”) warrants to each original retail purchaser (“Purchaser”) of its new products from the Company or its 
authorized distributor that such products are, at the time of delivery to the Purchaser, made with good material and workmanship.  No 
warranty is made with respect to: 
 
1. 

Any product which has been repaired or altered in such a way, in the Company’s judgment, as to affect the product adversely. 

 
2. 

Any product which has, in the Company’s judgment been subject to negligence, accident, improper storage, or improper installation or 
application. 

 
3. 

Any product which has not been operated or maintained in accordance with the recommendations of the Company. 

 
4. 

Components or accessories manufactured, warranted and serviced by others. 

 
5. 

Any reconditioned or prior owned product. 

 
Claims for items described in (4) above should be submitted directly to the manufacturer. 
 

WARRANTY PERIOD

 

The Company’s obligation under this warranty is limited to repairing or, at its option, replacing, during normal business hours at an authorized 
service facility of the Company, and part which in its judgment proved not to be as warranted within the applicable Warranty Period as 
follows. 
 

AIRENDS

 

Airends, consisting of all parts within and including the cylinder and gear housing, are warranted for 24 months from date of initial use or 27 
months from date of shipment to the purchaser, whichever occurs first. 
 
Any disassembly or partial disassembly of the  airend, or failure to return the “unopened” airend per Company instructions, will be cause for 
denial of warranty. 
 

MAJOR PACKAGE COMPONENTS

 

The drive motor, air or water cooled coolers and the AutoSentry Controller are warranted for 24 months from date of initial use or 27 months 
from date of shipment to the first purchaser,  whichever occurs first. 
 

OTHER COMPONENTS

 

All other components are warranted for 12 months from date of initial use or 15 months from date of shipment to first purchaser, whichever 
occurs first. 
 

LABOR TRANSPORTATION AND INSPECTION

 

The Company will provide labor, by Company representative or authorized service personnel, for repair or replacement of any product or part 
thereof which in the Company’s judgment is proved not to be as warranted.  Labor shall be limited to the amount specified in the Company’s 
labor rate schedule. 
 
Labor costs in excess of the Company rate schedule amounts or labor provided by unauthorized service personnel is not provided for by this 
warranty. 
 
All costs of transportation of product, labor or parts claimed not to be as warranted and, of repaired or replacement parts to or from such 
service facilities shall be borne by the Purchaser.  The Company may require the return of any part claimed not to be as warranted to one of 
its facilities as designated by Company, transportation prepaid by Purchaser, to establish a claim under this warranty. 
 
Replacement parts provided under the terms of the warranty are warranted for the remainder of the Warranty Period of the product upon 
which installed to the same extent as if such parts were original components. 
 

DISCLAIMER

 

THE FOREGOING WARRANTY IS EXCLUSIVE AND IT IS EXPRESSLY AGREED THAT, EXCEPT AS TO TITLE, THE COMPANY MAKES 
NO OTHER WARRANTIES, EXPRESSED, IMPLIED OR STATUTORY, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY. 
 
THE REMEDY PROVIDED UNDER THIS WARRANTY SHALL BE THE SOLE, EXCLUSIVE AND ONLY REMEDY AVAILABLE TO 
PURCHASER AND IN NO CASE SHALL THE COMPANY BE SUBJECT TO ANY OTHER OBLIGATIONS OR LIABILITIES.  UNDER NO 
CIRCUMSTANCES SHALL THE COMPANY BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, 
EXPENSES, LOSSES OR DELAYS HOWSOEVER CAUSED. 
 
No statement, representation, agreement, or understanding, oral or written, made by any agent, distributor, representative, or employee of 
the Company which is not contained in this Warranty will be binding upon the Company unless made in writing and executed by an officer of 
the Company. 
 
This warranty shall not be effective as to any claim which is not presented within 30 days after the date upon which the product is claimed not 
to have been as warranted.  Any action for breach of this warranty must be commenced within one year after the date upon which the cause 
of action occurred. 
 
Any adjustment made pursuant to this warranty shall not be construed as an admission by the Company that any product was not as 
warranted. 

AU-20   R 9/01 

COPYRIGHT

©

 2000 Gardner Denver, Inc. 

 

 

Summary of Contents for INTEGRA EFB99A






















































Reviews: