background image

15

Cooling Water Requirements

38

°

F P.D.P

50

°

F P.D.P

Max. Refrig.

Cooling

Cooling

Max. Refrig.

Cooling

Cooling

Capacity

Water Flow

Water

Capacity

Water Flow

Water

Nominal

Water Valve

(BTU/HR)

Rate @ 85

°

F

Pressure

(BTU/HR)

Rate @ 85

°

F

Pressure Drop

Horsepower

Size

(GPM)

Drop (PSID)

(GPM)

(PSID)

7.5

1"

78,800

14.6

6.0

96,660

17.2

9.2

10

1"

117,600

21.0

10.3

143,400

25.6

16.7

15

1 1/4"

155,600

23.5

9.3

195,200

34.8

15.1

20

1 1/4"

166,160

30.8

9.8

206,880

36.9

18.6

25

1 1/2"

213,440

39.5

11.4

278,620

49.7

20.0

30

1 1/2"

247,340

45.8

16.6

306,680

54.7

26.0

35

2 1/2"

315,820

58.4

11.9

395,460

70.5

15.2

40

2 1/2"

385,600

71.3

12.2

468,420

83.5

17.7

50

2 1/2"

426,880

79.0

13.9

557,240

99.4

22.3

60

3"

494,680

91.5

2.6

613,360

109.4

2.9

70

3"

631,640

116.9

3.8

790,920

141.0

6.2

80

3"

747,320

130.3

3.1

929,800

185.3

3.4

100

4"

937,800

173.6

< 5*

1,150,400

213

< 5 *

- Table valid for Copeland units only.

* No other data available.

- Cooling water @85

°

F - for other conditions consult manufacturer.

Summary of Contents for RHC Series





















Reviews: