Gardol GLH-S-2800 Translation Of Original Instruction Manual Download

Page: 24 / 168

www.scheppach.com

24 | GB

Setting the counter blade

The counter blade and the blade cylinder have

been ideally adjusted by the manufacturer.

Re-adjusting the counter blade is only required if

it becomes worn. For maximum performance, it

is necessary that the distance between the coun-

ter blade and blade cylinder is about 0.50 mm.

• Turn the shredder on.
• Turn the adjustment wheel (9) clockwise until you

can hear slight grinding sounds.

• When turning the adjustment wheel (9) clockwise

by half a turn, the blade cylinder is positioned clos-
er to the counter blade by 0.50 mm.

WARNING: If the shredder blade touches the

counter blade, it will be trimmed and small pieces

of swarf may fall out of the ejection opening. This

is not an error, but it has to be re-adjusted to the

required degree because otherwise the counter

blade will wear too early.

Overload protection

In the event of overload, e.g. due to branches that are
too thick, the equipment automatically switches off.
After a short cooling period (approximately 5 min-
utes), press the reset switch (12).

10. Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies

with the applicable VDE and DIN provisions.

The customer‘s mains connection as well as

the extension cable used must also comply with

these regulations.

Damaged electrical connection cable

The insulation on electrical connection cables is of-
ten damaged.
This may have the following causes
• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been im-

properly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insulation
damage.
Check the electrical connection cables for damage
regularly. Make sure that the connection cable does
not hang on the power network during the inspection.
Electrical connection cables must comply with the
applicable VDE and DIN provisions. Only use con-
nection cables with the marking „H05VV-F“.

• Repeat the above steps on the opposite side

(Fig. F).

2. Assembling the stand to the machine body

(Fig. G/H)

• Fit the supporting feets (3) onto the threaded bolts

(18) of the machine body (Fig. G)

• Fit the supplied lock nuts (16) by hand (Fig. G) and

tighten them with the wrench (a) (Fig. H).

3. Attaching the Collecting bag (Fig. I/K)
To collect the chopped material, attach the supplied
collecting bag (6) to the hooks provided (Fig. H).

9. Operation

Control panel (Fig. A)

• On switch (7):

Pressing this button starts the

shredder.

•

Off switch (8):

Pressing this button stops the

shredder.

Switch for roll rotation direction (11):

•

Button „▲“ - anti-clockwise: When this button is

pressed, the blade cylinder rotates anti-clockwise.
This is necessary when jammed shredding materi-
al needs to be freed. This function is only available
when the shredder is in operation.

•

Button „▼“ - clockwise: This button switches the

direction of the blade cylinder from anti-clockwise
back to clockwise.

Reset-switch (12):

Overload protection

Working with the shredder

Alternating with branches, shred withered gar

den waste and branches that have been stored

several days to prevent the shredder from be

coming blocked.

•  Connect the shredder to the power supply.
•  Turn the shredder on by using the on switch (7).
•  Fill shredding material into the feed hopper and it

will be drawn in.

• Caution

: If the material becomes jammed, first

press the red off switch (8) to stop the device. Push
the switch for roll rotation direction (11) downwards
to the “ = “ sign. Start the device by pressing the
green on switch (7). Stop the device by pressing
the red off switch (8). Remove the jammed material.
Push the switch (11) to the “ - “ sign. The device is
ready for operation.

•

Make sure the shredder has completely shred

ded the input material before adding new.

• Do not use your hands to push in more shredding

material. Use the special pushing device (c) or oth-
er shredding material.

•

When you have finished working with the shredder,

turn it off and disconnect it from the mains.