English
English
33/132
6. START UP INSTRUCTIONS
6.1.LIST OF MATERIALS
This machine includes the following elements that you
will find inside the box:
• Machine.
• Tools.
• Cutting accessories.
• Instruction manual.
Ensure that all elements listed above are included with
the machine. Thanks to the quality control checks at
the factory it is highly unlikely that any elements will
be missing. If you were to find any element missing,
do not use the machine until the defect has been
repaired or the machine is complete.
Using the machine with defective parts or without all
the elements can cause severe personal damages.
6.2 MOUNTING THE DRILL
1. Lift the blocking bobby pin.
2. Remove the bobby pin.
3. Place the drill aligning the pin holes of the drill with
he axis of the machine.
4. Insert the bobby pin.
5. Secure the blocking mechanism of the bobby pin.
6.3. FUEL
IMPORTANT: The fuel used is highly
inflammable. If the fuel or the machine
catch fire, fight the flames with a dry dust
fire extinguisher.
Do not smoke while preparing or refueling.
Do not approach any flame or hot element
to the fuel.
Use unleaded fuel of 95° and synthetic
oil for 2 stroke engines. Motor Fuel:
Mixture (Gasoline 40: Oil 1) 2.5%.
Mix gasoline and oil in a bottle
homologated for this use. If you will mix more
combustible just prepare the amount you will use the
short term.
Do not use fuel that has been stored over two months.
The fuel stored for long periods lose its characteristics
making it harder to start the engine and giving poorer
performance.
6.4. FILLING THE FUEL TANK:
1. Choose an open are ato perform this situation
2. Stay away from the area where you have made the
preparation of the mixture.
3. Remove the combustible tank cap and fill with fuel.
4. Close tighly the fuel cap and remove all traces of
fuel that have been spilled with a rag.
WARNINGS:
- Always switch off the engine before refueling.
- Do not start the machine in a closed area. The
exhaust fumesand the vapours of the petrol all
contain carbon monoxide and other
dangerous chemical substances. In case of gas
concentration due to insufficient ventilation,
eliminate from the work area everything that
1
2
3
4
5
Summary of Contents for 932 G
