English
English
37/132
Allow the machine to rest on the soil maintain the par
speed of the engine.
The drill will start to make the hole slowly aided by
the weight of the machine. Do not push the machine
downwards to try and finish the hole more quickly as
you will force the working components of the machine
and therefore you will cut its working life.
When the sufficient depth has been achieved, reduce
the engine power and at the same time pull the
machine slowly out of the hole.
When the drill has been fully removed from the soil,
leave the engine idle and switch the machine off.
When the drill has stopped turning, leave the machine
on the ground leaning on the drill and with the petrol
deposit in a horizontal position.
Tips:
If the soil is soft you will be able to do the hole with
any drill but if the soil is hard, we recommend you
first do an initial hole with the drill with the smallest
diameter, then carry on with the middle drill and finally
with the drill with the biggest diameter.
8. MAINTENANCE AND SERVICE
Make periodic inspections of the machine to ensure
that the machine is correct. For a thorough inspection
take the machine to your dealer.
It is necessary to stop the engine and to check
that the cutting tool is stopped before cleaning or
transporting the machine.
Before performing any maintenance or repair
the machine make sure the engine is off and
remove the spark plug cap. Perform all
maintenance of the machine when is set on a flat and
clear surface.
Never try adjustments in the machine if it is running
and / or attache to the user by the harness. Perform
all maintenance of the machine when is set on a flat
and clear surface.
Warning! Do not modify the machine or change
the cutting elements. An inadequate use of these
elements can cause serious personal damages and
can even be fatal.
Use only suitable spares to get a proper performance
for this machine. This replacement can be found on
the official distributor of the machine. Using other
sparks may causes risks, damage to the user or
people around the machine.
Carburetor adjustment is complicated and should
be done only by the service.Carburetor regulation
is complicated and should only be carried out by a
service agent.
An incorrect regulation of the carburetor can cause
damages to the engine and is sufficient motive to
cancel the warranty.
The removal of security devices, an improper
maintenance, the substitution of elements with non
original elements can cause corporal damages.
8.1. CARE AND MAINTENANCE AFTER USE
Carry out the following operations when you have
finished the work to ensure that the machine is kept in
a perfect condition.
8.1.1. GENERAL MAINTENANCE
Keep clean the machine, especially the fuel tank area
and areas near the air filter.
Summary of Contents for 932 G
