background image

5

sticking of product. Never salt food over griddle since this will build up a gummy residue making
it difficult to clean.

Avoid hitting the surface of the griddle with the edge of a spatula since this will cause nicks. The
most  frequently  used  temperatures  are  149

•

C  to  182

•

C  (300

•

F  to  360

•

F).  After  one  cycle,  the

griddle plate will discolour. This is normal and will not affect cooking performance.

Check the grease container and drain frequently during heavy use to prevent overflow.

OPERATING THE GRIDDLE:

NOTE: 

Ensure the electrical supply to the appliance is turned "ON".

1.

 

Switch “ON” main power switch on the control panel.

2.

 

Switch “ON” desired section(s).

3.

 

Set the thermostat to the desired temperature.

SHUTTING THE GRIDDLE DOWN:

1.

 

Set the thermostat to the OFF  position.

2.

 

Switch “OFF” all sections.

3.

 

Switch “OFF” main power switch on the control panel.

MAINTENANCE & CLEANING

CLEANING:

STAINLESS STEEL:

Stainless  steel  should  be  cleaned  using  a  mild  detergent,  a  soft  cloth  and  hot  water.  If  it  is
necessary to use a non-metallic scouring pad, always rub in the direction of the grain in the metal

Summary of Contents for ECG













Reviews: