background image

Part Number  4532292   Rev 3   12/15 3

 

Safety Notices

Safety Notices

DEFINITIONS

 DANGER

Indicates a hazardous situation that, if not avoided, will 

result in death or serious injury. This applies to the most 

extreme situations.

n

Warning

Indicates a hazardous situation that, if not avoided, 

could result in death or serious injury.

,

Caution

Indicates a hazardous situation that, if not avoided, 

could result in minor or moderate injury. 

Notice

Indicates information considered important, and is used 

to address practices not related to physical injury. For 

example, messages relating to property damage.

NOTE: Indicates useful, extra information about the 

procedure you are performing.

Reference: ANZI Z535.6-2011

SAFETY SYMBOLS AND WARNINGS ON THE APPLIANCE

This symbol alerts you to a hazardous situation 

that WILL or COULD cause serious bodily harm 

or death. Be alert and implement relevant safety 

precautions.

DANGER - HIGH VOLTAGE

This dangerous voltage warning symbol 

indicates a risk of electric shock and hazards 

from dangerous voltage.

Electromagnetic Field

  

Warning  

RISK OF FIRE OR ELECTRIC SHOCK! DO NOT OPEN!

To reduce the risk of fire or electric shock, do not remove or 

open cover. No user serviceable parts inside.

Refer servicing to qualified personnel.

CAUTION     

     ATTENTION

DISCONNECT FROM SUPPLY CIRCUIT BEFORE OPENING

DISCLAIMERS

 DANGER

Disregarding any safety instructions may cause harm to 

people, the surroundings, and the equipment. Garland 

is not responsible for any damages or personal injury 

caused by failure to observe any safety requirements. 

Risks involved when disregarding safety precautions 

include, but not limiting to: 

•  Death or injury caused by electric shock.
•  Burn injury caused by contacting overheated cooking 

surface, cookware, or oil and grease.

•  Damage to the equipment caused by using 

unsuitable cookware.

 DANGER

Do not install or operate equipment and/or accessories 

that have been misused, abused, neglected, damaged, 

or altered from that of original manufactured 

specifications.

 DANGER

Contact the manufacturer if you intend to make any 

changes on the equipment. For safety reasons, always 

use genuine parts and accessories approved by the 

manufacturer or authorized representative. Refer to the 

warranty documents for your equipment.

 DANGER

Owners and operators are cautioned that maintenance 

and repairs must be performed by an authorized service 

agent using only genuine replacement parts. The 

manufacturer will have no obligation with respect to any 

product that has been improperly installed, adjusted, 

operated or not maintained in accordance with national 

and local codes and/or installation instructions provided 

with the product or any product that has its serial 

number defaced, obliterated or removed, and/or which 

has been modified or repaired using unauthorized parts 

or by unauthorized service agents. 

 DANGER

Improper installation, adjustment, alteration, service, 

or maintenance of this appliance or installation of 

a damaged appliance can result in DEATH, INJURY, 

EQUIPMENT DAMAGE, and void the warranty. 

 DANGER

All utility connections and fixtures must be maintained 

in accordance with local and national codes.

Summary of Contents for GI-SH/GR 3500

































Reviews: