background image

Document #  G_GHD_OM_PASTACUISINE_4607873 – 08/21

 11

OPERATING INSTRUCTIONS Continued

1

Numeric Keypad

6

Skim Switch

2

Boil Mode Indicator

7

Timer Start Switch

3

Boil Mode Switch

8

Simmer Mode Switch

4

Power Switch

9

Simmer Mode 

Indicator

5

LED Display

10

Trouble Light

Controller

The Pasta Magic Controller allows the operator to specify 

a cook time in minutes and seconds, and then initiate 

a cooking cycle.  This controller is available in three 

configurations.  The standard configuration has both 

automatic filling (Autofill) and automatic skimming 

(Autoskim) features.  Options include Autofill only, or neither 

Autofill nor Autoskim.

When in the 

BOIL

 mode, the burners are lit at all times.  It is 

used when actually cooking pasta.

The 

SIMMER

 mode feature maintains the water temperature 

just below boiling, which conserves energy and water.  This 

feature is designed for rethermalizing previously cooked 

packaged products and for keeping the cooker in standby.

The 

AUTOSKIM

 and 

SKIM

 features are independent of each 

other.  The 

AUTOSKIM

 feature, on units so equipped, adds 

water for approximately 3 seconds once a minute.  It cannot 

be turned off.  

The 

SKIM

 feature, when activated by pressing the skim 

button on the controller, delivers a continuous spray of 

water for approximately 2 minutes, and then stops until 

the button is again pressed.  In both cases, the purpose 

is to cause the water in the cookpot to overflow into the 

drain, carrying floating starch with it.  (A buildup of starch 

reduces the efficiency of the cooker and can cause erroneous 

temperature and water level sensing.) 

NOTE

:  Do not use 

deliming solution to clean these units. Use of deliming 

solution will damage all stainless steel parts).

LOW WATER SENSING 

automatically closes the gas valve 

(thereby extinguishing the burner flame) if the water in the 

cookpot drops too low.  When the water level in the cookpot 

is below the low-water sensor, such as when draining and 

cleaning the cookpot, the controller display will read 

LO

.  

NORMAL WATER LEVEL SENSING

, on units configured with 

the Autofill feature, water is automatically added during or 

after a cooking cycle if the water in the cookpot drops to 

a level lower than approximately 1¼-inch (32 mm) below 

the overflow drain.  With this automatic filling feature, the 

water level does not have to be continuously monitored.  The 

cookpot always has the correct amount of water.

FAHRENHEIT OR CELSIUS TEMPERATURE DISPLAY.

 

There are two versions of the SMS Controller: one that can 

be toggled between Fahrenheit and Celsius temperature 

display, and one that cannot.  To determine which version 
you have, turn the controller off by pressing the power 

 

switch.  The display will go blank.  Press the Simmer button  

 

(right thermometer icon).  If 

CODE

 appears in the display, 

the temperature display can be changed.  If not, the display 

cannot be changed.

1. If 

CODE

 appears in the display, press 1, 6, 5, 8.  The display 

will be toggled from Fahrenheit to Celsius or from Celsius 

to Fahrenheit.

2.  Press the Boil button 

 (left thermometer icon) to 

display the cookpot temperature.  If an 

F

 follows the 

temperature, the display is in Fahrenheit; if a 

C

 follows the 

temperature, the display is in Celsius.

Summary of Contents for PASTA MAGIC

























Reviews: