background image

Document #  G_GHD_OM_PASTACUISINE_4607873 – 08/21

6

INSTALLATION INSTRUCTIONS

burner operation.

The cooker flue opening must not be placed close to the 

intake of the exhaust fan, and the cooker must never have its 

flue extended in a “chimney” fashion.  An extended flue will 

change the combustion characteristics of the cooker, causing 

longer recovery time.  It also frequently causes delayed 

ignition.

When installed beneath a ventilation hood, adequate 

distance must be maintained from the flue outlet of the 

cooker to the lower edge of the ventilation filter bank.  Filters 

should be installed at an angle of 45° with a drip tray placed 

beneath the lowest edge of the filter.  For U.S. installation, 

NFPA standard No. 96 states, “A minimum distance of 18 

inches (450mm) should be maintained between the flue 

outlet and the lower edge of the filter.”

For installations in other than the United States, installers 

should contact the appropriate local or national agency 

for information on the construction and installation of 

ventilating hoods.

,

CAUTION

DO NOT install this appliance directly over a drain 

opening.

ELECTRICAL GROUNDING REQUIREMENTS

All electrically operated appliances must be grounded in 

accordance with all applicable national and local codes.  A 

wiring diagram is located on the inside of the cooker door.  

Refer to the rating plate on the inside of the cooker door for 

the proper voltages.  

 DANGER

If this appliance is equipped with three-prong 

(grounding) plug, it must be plugged directly into a 

properly grounded receptacle.  Do not cut or remove the 

grounding prong from the plug.

 DANGER

This equipment requires electrical power for operation.  
Place the gas control valve in the OFF position in case of 

a prolonged power outage.  
Do not attempt to use the equipment during a power 

outage.  

General Installation Requirements

Qualified, licensed, and/or authorized installation 

or service personnel, as defined in Section 1.5 of this 

manual, should perform all installation and service on 

Garland equipment.  

Conversion of this appliance from one type of gas to 

another should only be performed by qualified, licensed, 

and/or authorized installation or service personnel as 

defined in section - Installation, Operating and Service 

Personnel.

Failure to use qualified, licensed, and/or authorized 

installation or service personnel as defined in section - 

Installation, Operating and Service Personnel, to install, 

convert to another gas type, or otherwise service this 

equipment will void the Garland warranty and may result 

in damage to the equipment or injury to personnel.

Where conflicts exist between instructions and 

information in this manual and local or national codes or 

regulations, installation and operation shall comply with 

the codes or regulations in force in the country in which 

the equipment is installed.

Upon arrival, inspect the cooker carefully for visible or 

concealed damage.  (See 

Shipping Damage Claim 

Procedure.

)

CLEARANCE AND VENTILATION

The cooker(s) must be installed with 6 inches (150mm) 

clearance at both sides and back when installed adjacent 

to combustible construction; no clearance is required 

when installed adjacent to noncombustible construction. 

A minimum of 24 inches (600mm) clearance should be 

provided at the front of the cooker.  To provide the airflow 

necessary for good combustion and burner operation, the 

areas surrounding the cooker front, sides and rear must be 

kept clear and unobstructed.  

 DANGER

This appliance must be installed with sufficient 

ventilation to prevent the occurrence of unacceptable 

concentrations of substances harmful to the health of 

personnel in the room in which it is installed.

One of the most important considerations of efficient cooker 

operation is ventilation.  Cookers must be installed in an area 

with an adequate air supply and adequate ventilation. Make 

sure the cooker is  installed so that products of combustion 

are removed efficiently, and that the kitchen ventilation 

system does not produce drafts that interfere with proper 

Summary of Contents for PASTA MAGIC

























Reviews: