Garmin dezlCAM, Owner'S Manual

The Garmin Express software downloads and installs the 

updates onto your device. Map updates are very large, and this 

process may take a long time on slower Internet connections.

Data Management

You can store files on your device. The device has a memory 

card slot for additional data storage.

NOTE: 

The device is not compatible with Windows 95, 98, Me, 

Windows NT

®

, and Mac OS 10.3 and earlier.

About Memory Cards

You can purchase memory cards from an electronics supplier, 

or purchase pre-loaded Garmin mapping software 

(

www.garmin.com

). In addition to map and data storage, the 

memory card can be used to store files such as maps, images, 

geocaches, routes, waypoints, and custom POIs.

Installing a Memory Card for Maps and Data

You can install a memory card to increase the storage space for 

maps and other data on your device. You can purchase memory 

cards from an electronics supplier, or go to 

www.garmin.com

/maps

 to purchase a memory card with pre-loaded Garmin 

mapping software. The device supports microSD and 

microSDHC memory cards.

1

Insert a memory card 

À

 into the slot 

Á

.

2

Press it in until it clicks.

Connecting the Device to Your Computer

You can connect the device to your computer using a USB 

cable.

1

Plug the small end of the USB cable into the port on the 

device.

2

Plug the larger end of the USB cable into a port on your 

computer.
A picture of your device connected to a computer appears on 

the device screen.
Depending on your computer operating system, the device 

appears as either a portable device, a removable drive, or a 

removable volume.

Transferring Data From Your Computer

1

Connect the device to your computer (

Connecting the Device 

to Your Computer

, page 21

).

Depending on your computer operating system, the device 

appears as either a portable device, a removable drive, or a 

removable volume.

2

On your computer, open the file browser.

3

Select a file.

4

Select 

Edit

 > 

Copy

.

5

Browse to a folder on the device.

NOTE: 

For a removable drive or volume, you should not 

place files in the Garmin folder.

6

Select 

Edit

 > 

Paste

.

Disconnecting the USB Cable

If your device is connected to your computer as a removable 

drive or volume, you must safely disconnect your device from 

your computer to avoid data loss. If your device is connected to 

your Windows computer as a portable device, it is not necessary 

to safely disconnect.

1

Complete an action:
• For Windows computers, select the 

Safely Remove 

Hardware

 icon in the system tray, and select your device.

• For Mac computers, drag the volume icon to the trash.

2

Disconnect the cable from your computer.

Viewing GPS Signal Status

Hold 

 for three seconds.

Power Cables

Your device can be powered various ways.
• Vehicle power cable
• USB cable
• AC adapter (optional accessory)

Charging the Device

NOTE: 

This Class III product shall be powered by an LPS power 

supply.
You can charge the battery in the device using any of these 

methods.
• Connect the device to the vehicle power cable.
• Connect the device to a computer using a USB cable.

The device may charge slowly when connected to a 

computer. Some portable computers may not charge the 

device.

• Connect the device to an optional power adapter accessory, 

such as a wall power adapter.
You can purchase an approved Garmin AC-DC adapter 

suitable for home or office use from a Garmin dealer or 

www.garmin.com

.

Changing the Fuse in the Vehicle Power Cable

NOTICE

When replacing the fuse, do not lose any of the small pieces 

and make sure they are put back in the proper position. The 

vehicle power cable does not work unless it is assembled 

correctly.

If your device does not charge in your vehicle, you may need to 

replace the fuse located at the tip of the vehicle adapter.

1

Rotate the end piece 

À

 90 degrees counter clockwise to 

unlock it.

TIP: 

You may need to use a coin to remove the end piece.

2

Remove the end piece, the silver tip 

Á

, and the fuse 

Â

.

3

Insert a new fast-blow fuse that has the same current, such 

as 1 A or 2 A.

4

Place the silver tip in the end piece.

Appendix

21