background image

Specifications

All Models

Material

Polycarbonate plastic

Water rating

IEC 60529 IPX7

1

Temperature range

From -15° to 55°C (from 5° to 131°F)

Input voltage

From 9 to 18 Vdc

Fuse

3 A, fast-acting (included)

Memory card

1 microSD

®

 card slot; 32 GB max. card size

Display resolution (W x H)

800 x 480 pixels

Display type

WVGA

Sonar frequencies

2

Traditional: 50/200, 77/200, 83/200 kHz
Single Channel CHIRP: from 40 to 250 kHz
Garmin ClearVü CHIRP: 260/455/800 kHz

Sonar transmit power (RMS)

3

CHIRP: 500 W
Garmin ClearVü CHIRP: 500 W

Sonar depth

4

701 m (2,300 ft.) at 77 kHz

5x Models

Dimensions, chartplotter only (W x H x D)

188 x 122 x 61.5 mm (7

3

/

8

 x 4

13

/

16

 x 2

7

/

16

 in.)

Dimensions, in bail mount with sun cover (W x H x D)

212 x 143.3 x 100 mm (8

3

/

8

 x 5

5

/

8

 x 3

15

/

16

 in.)

Display size (W x H)

109 x 65.8 mm (4

5

/

16

 x 2

9

/

16

 in.)

127.3 mm (5 in.) diagonal

Clearance to nearest obstruction behind chartplotter

57 mm (2

1

/

4

 in.)

Weight

0.5 kg (1.1 lb.)

Max. power draw

8.4 W

Typical current draw at 12 Vdc (RMS)

600 mA

Max. current draw at 12 Vdc (RMS)

700 mA

Wireless frequency

2.4 GHz @ 19.7 dBm maximum

Compass-safe distance

7.62 cm (3 in.)

The device withstands incidental exposure to water of up to 1 m for up to 30 min. For more information, go to 

www.garmin.com/waterrating

.

Dependent upon the transducer.

Dependent upon the transducer rating and depth.

Dependent upon the transducer, water salinity, bottom type, and other water conditions.

9

Summary of Contents for ECHOMAP UHD2 5X











Reviews: