Do not connect the wiring harness to the stereo until after all
of the bare wire connections have been made.
4
Connect the black wire to the negative (-) battery terminal.
5
Connect the power wire to the ignition or another manual
switch, and connect the switch to the positive (+) battery
terminal if necessary.
6
Connect the wiring harness plug to the stereo.
NMEA 2000 System Wiring Diagram
À
Stereo
Á
NMEA 2000, such as a supported chartplotter MFD or NRX200i
remote
Â
In-line switch
Ã
NMEA 2000 power cable
Ä
NMEA 2000 cable from the stereo
This can be extended to a maximum length of 6 m (20 ft.) using a
NMEA 2000 cable.
Å
NMEA 2000 drop cable from the chartplotter MFD
Æ
9 to 16 Vdc power supply
Ç
NMEA 2000 terminator or backbone cable
È
NMEA 2000 T-connector
É
NMEA 2000 terminator or backbone cable
Stereo Information
Specifications
Specification
Measurement
Dimensions (black box stereo)
(W × H × D)
Approximately 55 mm (2.17 in.) ×
60 mm (2.63 in.) × 94 mm (3.70 in.)
Water resistance (black box
stereo)
IEC 60529 IPX3
Water resistance (remote
control)
IEC 60529 IPX7 (front), IEC 60529
IPX3 (rear)
Operating temperature
From 0 to 50°C (from 32 to 122°F)
Storage temperature
From -20 to 70°C (from -4 to
158°F)
Input voltage
From 10.8 to 16 Vdc negative
ground
Fuse rating
15 A
NMEA 2000 LEN
1 (50 mA)
Compass-safe distance
15 cm (5.91 in.)
Pre-output voltage
3 V peak
Current (standby)
less than 15 mA
Current (max.)
15 A
Output music power per
channel
50 W
Specification
Measurement
Total output music power
200 W
Speaker impedance
4 Ohm per channel
Total harmonic distortion (1 W
output, 4 ohm load, from 20 Hz
to 20 kHz)
0.04 typical
Less than 0.1% max.
Tuner
Europe and
Australasia
USA
Japan
FM radio
frequency
range
87.5 to
108 MHz
87.5 to
107.9 MHz
76 to 90 MHz
FM frequency
step
50 kHz
200 kHz
50 kHz
AM radio
frequency
range
522 to
1620 kHz
530 to
1,710 kHz
522 to 1,620 kHz
AM frequency
step
9 kHz
10 kHz
9 kHz
Remote Control Dimensions
Item
Measurement
À
54 mm (2.13 in.)
Á
46 mm (1.81 in.)
Â
65 mm (2.56 in.)
Ã
56.5 mm (2.22 in.)
USB Device Compatibility
You can use a USB flash drive or the USB cable included with
your media player to connect a media player or mobile device to
the USB port.
The stereo is compatible with iAP2 Apple
®
devices such as the
iPhone
®
6s Plus, iPhone 6s, iPhone 6 Plus, iPhone 6, iPhone 5s,
iPhone 5c, iPhone 5, and iPod touch
®
(5th and 6th generation).
The stereo is compatible with Android
™
devices that support the
Android Open Accessory (AOA) protocol.
NOTE:
The stereo is not compatible with Android devices in
MTP or PTP mode. See the instructions for your Android device
to connect using AOA, if necessary.
The stereo is compatible with media players and other USB
mass storage devices, including USB flash drives. Music on
USB drives must meet these conditions:
• The USB mass storage device must be formatted using the
FAT32 file system.
• The music files must be formatted as MP3 files.
• Each folder on the storage device can contain a maximum of
250 MP3 files.
Registering Your BB100
Help us better support you by completing our online registration
today.
• Go to
.
• Keep the original sales receipt, or a photocopy, in a safe
place.
BB100 Installation Instructions
3
