Garmin G3X Touch Installation Manual Download | Manualshive

Page: 228 / 848

background image

190-01115-01

G3X/G3X Touch Installation Manual - GPS/XM Antenna Installation

Rev. AC

Page 22-8

Mounting the antenna under the glare shield (Figure 22-3) is a good option for XM – FIS antennas,
although it is not typically the best option for a GPS antenna. This location results in the aft fuselage
shading the antenna.

Figure 22-3 Glare Shield Buried Antenna Area

NOTE

Due to the excessive temperature environment and large areas of signal blockage caused
by the fuselage, mounting the antenna under the engine cowling (forward of the firewall)
is not recommended and likely will not provide adequate GPS reception.

22.3.4 Antenna Doubler/Backing Plate

The antenna installation must provide adequate support for the antenna considering a maximum drag load
of 5 lbs. (at subsonic speed). When penetrating the skin with a large hole (i.e. for the coax connector) a
doubler plate is required to re-instate the integrity of the aircraft skin. Never weaken the aircraft structure
when choosing a mounting area. Make use of any available reinforcements where appropriate.

22.3.5 Antenna Grounding Plane

Although no ground plane is required, the antennas typically perform better when a ground plane is used.
The ground plane should be a conductive surface as large as practical, with a minimum diameter of 8
inches. To use an antenna in aircraft with fabric or composite skin, a ground plane is recommended. It is
usually installed under the skin of the aircraft, below the antenna, and is made of either aluminum sheet or
of wire mesh.

22.3.6 Antenna Grounding

The antenna is grounded through the mounting hardware and the coax connection. The mounting
hardware (washers and nuts) and doubler plate should make contact with an unpainted grounded surface
ensuring proper antenna grounding. It is important to have good conductivity between the coaxial shield
and the ground plane. The bottom of the antenna does not need to make contact with the ground plane (i.e.
the surface may be painted). The antenna will capacitively couple to the ground plane beneath the paint or
aircraft cover.

«
...
226
227
228
229
230
...
»

Summary of Contents for G3X Touch

















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for G3X Touch

SkyView SV-D1000

Brand: Dynon Avionics Pages: 154

Brand: Kanardia Pages: 63

Display Case Parameter Settings Service

Brand: Foster Pages: 17

Brand: Data Display Pages: 37

Setauket Fire Dept.

Brand: Data Display Pages: 39

Farmingville FD

Brand: Data Display Pages: 38

Brand: Data Display Pages: 39

Brand: Garmin Pages: 14

Brand: EPIC OPTIX Pages: 2

Addenda SHS9251

Brand: Structural Concepts Pages: 17

Brand: Roller Grill Pages: 7

Brand: Jupiter Avionics Pages: 16

Brand: Becker Pages: 32

Brand: Becker Pages: 39

Woodson W.HFHSQ23

Brand: STODDART Pages: 16

Brand: Vollrath Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands