Garmin GHP Reactor Mechanical Installation Instructions Manual Download

Page: 16 / 16

the rudder to the farthest position that does not report an

error.

Calibrate Rudder Center

: Initiates a procedure that establishes

the center position of the rudder. You can use this calibration

if the on-screen rudder position indicator does not match the

true rudder center on your boat.

Registering Your Device

Help us better support you by completing our online registration

today.
• Go to

http://my.garmin.com

• Keep the original sales receipt, or a photocopy, in a safe

place.

Contacting Garmin Product Support

• Go to

www.garmin.com/support

and click

Contact Support

for in-country support information.

• In the USA, call (913) 397.8200 or (800) 800.1020.
• In the UK, call 0808 2380000.
• In Europe, call +44 (0) 870.8501241.

Garmin

and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. GHP

™

, GHC

™

, Reactor

™

, and Shadow Drive

™

are trademarks of Garmin Ltd. or its

subsidiaries. These trademarks may not be used without the express permission of Garmin.
NMEA

, NMEA 2000

, and the NMEA 2000 logo are trademarks of the National Marine Electronics Association.

www.garmin.com/support

Summary of Contents for GHP Reactor Mechanical

















Search results

Summary of Contents for GHP Reactor Mechanical

Reviews:

Related manuals for GHP Reactor Mechanical

Brands by name

Popular brands

Garmin GHP Reactor Mechanical, Installation Instructions Manual

Search results

Summary of Contents for GHP Reactor Mechanical

Reviews:

Related manuals for GHP Reactor Mechanical

Brands by name

Popular brands