background image

GMA 340 Installation Manual

Page 1-3

190-00149-01

Rev. L

SPECIFICATION

CHARACTERISTIC

Intercom

Positions:  6 (pilot, copilot, 4 passengers)
Volume controls:  3 (pilot, copilot, passengers)
VOX level controls:  2 (pilot, copilot/passengers)
VOX circuits:  6 (one per mic input)
Music inputs (stereo):  2 (1 in Dual ADF version) (one input mutable)
Music input impedance:  460 ohms minimum
Music input level:  Less than 500 mVac RMS for full output (typical).

1 Vac RMS MAX (3 Vac p-p)

Microphone signal processing:  9 pole characteristic and special cabin

noise band de-emphasis

Intercom isolation modes:  3
Special functions:  Configurable aural push-button annunciation for

the crew

Headphone Outputs

Output amplifiers:  3, stereo (pilot, copilot, passengers)

Fidelity:   Power into 150

ȍ

       Distortion

                            50 mW                  <0.5%
                          100 mW                  <5%
Frequency response:  music;  100 Hz to 15 kHz nominal
Aircraft radio:  100 Hz to 6 kHz nominal
ICS mic:  (Special cabin noise band de-emphasis)

Speaker Outputs

Outputs selectable:  1, pilot selectable
Output power:  10 Watts into 4 or 8

ȍ

, @ any normal supply voltage.

Frequency response:  350 Hz to 6 kHz nominal
Special functions:  PA Mode, pilot selectable, including split operation

Marker Beacon Receiver

Frequency:  Crystal controlled at 75 MHz
Sensitivity:  LO 1000 µV hard;  HI 200 µV hard
Selectivity:  6 dB @ ±10 kHz min, 40 dB @ ±200 kHz max.
Input impedance:  50

ȍ

External lamp drive:  125 mA max each output
Other outputs:  Middle MKR sense
Special functions:

SmartMute

TM

marker audio muting

1.4

EQUIPMENT

GMA 340 Audio Panel, Ship Level Assembly, P/N 010-00152-( ) includes the following, depending on part
number:

011-00401-( )

GMA 340 Unit Assembly (011-00401-10 replaces 011-00401-00)

011-00652-00

Connector Kit, GMA 340

011-00678-00

Rack Backplate, GMA 340

115-00262-00

SMP, Install Rack, GMA 340

(The installation kit is the same for the GMA 340, GMA 340H and GMA 340 Dual ADF)

1.5

INSTALLATION ACCESSORIES

Marker beacon antenna kit (P/N 010-10175-00).  [Note: A marker beacon antenna approved to
TSO C35( ) that has been installed to meet the requirements of this manual may be approved for
use with the GMA 340].

Summary of Contents for GMA 340












































Reviews: