background image

Service Bulletin 2048

Page 2-10

April 24, 2020

Revision B

PURPOSE

GPS 175/GNX 375/GNC 355 Main Software Version 3.10 contains the following changes:

Adds support for additional FIS-B weather products:

Turbulence

Icing

G-AIRMET

Cloud Tops

Lightning

Center Weather Advisories

Updates NEXRAD “No Coverage” overlay to be semi-transparent

Adds support for database SYNC for transferring databases between Garmin displays – transfer 

and receive from any GI 275, GPS 175, GNX 375, or GNC 355 and receive only from G500 TXi/

G600 TXi

Improves availability for advisory guidance on LNAV approaches in areas without SBAS coverage

Fixes a problem where GAE 12 calibration was limited to 6 points

Adds Altitude Source Input Configuration setting to GPS 175 and GNC 355 to prevent nuisance 

messages when connected to Sandel 3308/3500/4500

Fixes an issue with GNC 355 carrier squelch setting. It is now applied when the value is changed

Adds GI 275 support

Adds Remote Radio Control Format 1 for GNC 355

ARINC 429 labels are transmitted when in config mode

DESCRIPTION

This modification consists of accessing the Garmin website and uploading GPS 175/GNX 375/GNC 355 

Main Software Version 3.10 to the GPS 175, GNX 375 or GNC 355.

COMPLIANCE

Optional:  This Service Bulletin may be incorporated at the owner’s discretion and is not warranty 

reimbursable.

APPROVAL

GPS 175/GNX 375/GNC 355 Main Software Version 3.10 is TSO authorized. 
Refer to the GPS 175 TSO Installation Manual (190-02207-00), GNX 375 TSO Installation Manual (190-

02207-04), or GNC 355 TSO Installation Manual (190-02488-00) for additional approvals. The change 

from GPS 175/GNX 375/GNC 355 Main Software Version 3.03 is minor per 14 CFR 21.619.

DOCUMENTATION CONSIDERATIONS

The GPS 175/GNX 375/GNC 355 SW V3.10 Upgrade Supplement (190-02488-02) Rev A is to be provided 

to the owner/operator when the update is complete. 

Summary of Contents for GNC 355











Reviews: