background image

190-02207-A2

GPS 175/GNX 375/GNC 355 Part 23 AML STC Maintenance Manual

Rev. 3

Page 3-7

3.4.3.2 Lighting Configuration

The 

Lighting Configuration

 page allows the user to configure the backlight and key lighting brightness 

display parameters. This page also allows the configuration of the photocell and the lighting bus settings.

3.4.3.3 Main System

The 

Main System

 allows the user to configure system related settings for the GPS 175/GNX 375/

GNC 355. Page settings include the following:

• Air/Ground Threshold

• Fuel Type

• GPS Select

• System ID

• RF Procedure Legs

• Ownship Icon

• Terrain Alerts

• Graphical Edit

• Composite CDI

• Bluetooth

• ADS-B Logging (GNX 375 Only)

• External FPL

• Altitude Source Input (GPS 175 and GNC 355 Only)

3.4.3.4 Main Indicator (Analog)

The 

Main Indicator (Analog)

 page allows the user to calibrate the OBS resolver and configure the selected 

course behavior.

3.4.3.5 XPDR (GNX 375 Only)

The 

XPDR Configuration

 page allows the user to configure the transponder related settings for the 

GNX 375. Page settings include the following:

• Sensors

• Options

• Test

• Airframe

• Flight ID

• Clear XPDR Settings

3.4.3.6 GPS Antenna Offset

The 

GPS Antenna Offset

 page allows the configuration of GPS antenna height, lateral offset, and 

longitudinal offset.

3.4.3.7 AHRS

The 

AHRS

 page allows the user to set the display orientation, yaw offset, and calibrate the internal AHRS. 

The Display Orientation must be set and the aircraft must be level before calibrating the internal AHRS.

Summary of Contents for GPS 175
































































































Reviews: