background image

2

Select 

Settings

 > 

Preferences

 > 

Screenshot Capture

 > 

On

.

3

Go to a screen you want to capture.

4

Hold 

HOME

 for at least six seconds.

Copying Screenshots to a Computer

1

Remove the memory card from the chartplotter, and insert it 

into a card reader that is attached to a computer.

2

From Windows Explorer, open the Garmin\scrn folder on the 

memory card.

3

Copy a .bmp file from the card and paste it to any location on 

the computer.

Troubleshooting

My device will not acquire GPS signals

If the device is not acquiring satellite signals, there could be a 

few causes. If the device has moved a large distance since the 

last time it has acquired satellites or has been turned off for 

longer than a few weeks or months, the device may not be able 

to acquire the satellites correctly.
• Ensure the device is using the latest software. If not, update 

the device software.

• Make sure the device has a clear view of the sky so the 

antenna can receive the GPS signal. If it is mounted inside of 

a cabin, it should be close to a window so it can receive the 

GPS signal.

My device will not turn on or keeps turning off

Devices erratically turning off or not turning on could indicate an 

issue with the power supplied to the device. Check these items 

to attempt to troubleshoot the cause of the power issue.
• Make sure the power source is generating power.

You can check this several ways. For example, you can 

check whether other devices powered by the source are 

functioning.

• Check the fuse in the power cable.

The fuse should be located in a holder that is part of the red 

wire of the power cable. Check that the proper size fuse is 

installed. Refer to the label on the cable or the installation 

instructions for the exact fuse size needed. Check the fuse to 

make sure there is still a connection inside of the fuse. You 

can test the fuse using a multimeter. If the fuse is good, the 

multimeter reads 0 ohm.

• Check to make sure the device is receiving is at least 10 V, 

but 12 V is recommended.
To check the voltage, measure the female power and ground 

sockets of the power cable for DC voltage. If the voltage is 

less than 10 V, the device will not turn on.

• If the device is receiving enough power but does not turn on, 

contact Garmin product support.

My device is not creating waypoints in the correct 

location

You can manually enter a waypoint location to transfer and 

share data from one device to the next. If you have manually 

entered a waypoint using coordinates, and the location of the 

point does not appear where the point should be, the map 

datum and position format of the device may not match the map 

datum and position format originally used to mark the waypoint.
Position format is the way in which the GPS receiver's position 

appears on the screen. This is commonly displayed as latitude/

longitude in degrees and minutes, with options for degrees, 

minutes and second, degrees only, or one of several grid 

formats.

Map datum is a math model which depicts a part of the surface 

of the earth. Latitude and longitude lines on a paper map are 

referenced to a specific map datum.

1

Find out which map datum and position format was used 

when the original waypoint was created.
If the original waypoint was taken from a map, there should 

be a legend on the map that lists the map datum and position 

format used to create that map. Most often this is found near 

the map key.

2

Select 

Settings

 > 

Preferences

 > 

Units

.

3

Select the correct map datum and position format settings.

4

Create the waypoint again.

Contacting Garmin Support

• Go to 

support.garmin.com

 for help and information, such as 

product manuals, frequently asked questions, videos, and 

customer support.

• In the USA, call 913-397-8200 or 1-800-800-1020.
• In the UK, call 0808 238 0000.
• In Europe, call +44 (0) 870 850 1241.

Specifications

Specifications

Device

Specification

Measurement

All models

Temperature range

From -15° to 50°C (from 5° to 
122°F)

Material

Polycarbonate plastic and die-
cast aluminum

Water rating

1

IEC 60529 IPX7

Input voltage

From 10 to 32 Vdc

Fuse

6 A, 125 V fast-acting

NMEA 2000 LEN

2

NMEA 2000 draw

75 mA max.

Compass-safe 
distance

65 cm (25.5 in.)

Max. waypoints

5,000

Max. routes

100

Max. active track 
points

50,000 points, 50 saved tracks

Memory card

2 SD

®

 card slots; 32 GB max. 

card size

Wireless frequency 
and protocols

Wi

Fi, ANT

®

, and Bluetooth 

technologies
2.4 GHz @ 15.26 dBm 
nominal

Ten-inch 
models

Dimensions (W x H x 
D)

318 x 185 x 69 mm (12 

1

/

2

 x 7 

5

/

16

 x 2 

11

/

16

 in.)

Weight

1.85 kg (4.1 lb.)

Display size (W x H)

224 x 125 mm (8 

3

/

4

 x 4 

15

/

16

 in.)

Display type

WSVGA

Display resolution

1024 x 600 pixels

Max. power usage at 
10 Vdc

32.4 W

Typical current draw at 
12 Vdc

1.9 A

Max. current draw at 
12 Vdc

2.7 A

Twelve-inch 
models

Dimensions (W x H x 
D)

359 x 227 x 69 mm (14 

1

/

8

 x 8 

15

/

16

 x 2 

11

/

16

 in.)

Weight

2.34 kg (5.15 lb.)

Display size (W x H)

262 x 164 mm (10 

5

/

16

 x 6 

7

/

16

 in.)

56

Appendix

Summary of Contents for GPSMAP 1000 Series







































































Reviews: