19
GPSMAP 4000/5000 Series Installation Instructions
Wiring to a GPS 17 or GPS 17 HVS Antenna
If you already have a Garmin GPS 17 or GPS 17 HVS installed on your boat, you can wire it to the GPSMAP 4000/5000 series chartplotter
instead of installing the included GPS 17x. Wire the existing GPS 17 or GPS 17 HVS antenna to the included 19-pin NMEA 0183 cable as well
as to the power supply for the boat, referring to the diagram below. Use 22 AWG shielded wiring for extended runs of wire to the NMEA 0183
cable or GPS 17 HVS cable. Solder all connections and seal them with heat-shrink tubing.
NOTE:
If you are using more than one Garmin chartplotter over a Garmin Marine Network, do not wire more than one chartplotter to a GPS
antenna. The GPS signal is shared between multiple chartplotters connected to a Garmin Marine Network.
Wiring to a GPS 17 or GPS 17 HVS Antenna
+
-
>
>
>
>
BAttErY
10–35 Vdc
WIrE
CoLor
WIrE
CoLor
rED (PoWEr)
BLACk (GnD)
orAnGE (ACC. on)
GrEEn (DAtA out)
GrEEn/WHItE (DAtA In)
rED (PoWEr)
BLACk (GnD)
YELLoW (on)
BLuE (DAtA In)
WHItE (DAtA out)
FuSE
7.5 A - 42 V
FuSE
1 A
Garmin
GPSMAP 4000/5000 series
chartplotter
GPS 17 or
GPS 17 HVS
antenna
PoWEr
CABLE
nMEA 0183
CABLE
Marine Video Cable
The included Marine Video 17-pin cable allows input of NTSC (National Television System Committee)/PAL (Phase Alternate Line) composite
video sources, and PC monitor output (4008/4208/4010/4210/5008/5208 = VGA output, 4012/4212/5012/5212/5015/5215 = XGA output).
Marine Video inputs are only available on the chartplotter to which they are attached and will not transmit over the Garmin Marine Network.
➊
and
➋
VIDEO 1 and VIDEO 2 Inputs (RCA connectors) allow input from two separate NTSC/PAL compatible video devices, such as VCR,
DVD, TV, or a video camera. The chartplotter can display one video input at a time or alternate between the two. See the owner’s manual for
details. Sound from a video source must be attached to a separate stereo/audio system. The video output from video devices attaches to the
Video 1 (Black Cable) or Video 2 (Gray Cable) RCA connectors.
➌
Use the PC monitor output (HD 15-pin) connector for remote viewing of the chartplotter display on a computer monitor. The remote monitor
must be capable of at least VGA resolution and have multi-sync capability.
note
Connector
Pin
Function
➊
rCA-1
CEntEr
2
VIDEo 1 In (BLACk jACkEt)
rCA-1 outEr 6
VIDEo 1 In, GnD
➋
rCA-2
CEntEr
11
VIDEo 2 In (GrAY jACkEt)
rCA-2 outEr 15
VIDEo 2 In, GnD
➌
HD-15 PIn 1
1
VGA, AnALoG-rED
HD-15 PIn 2
4
VGA, AnALoG-GrEEn
HD-15 PIn 3
3
VGA, AnALoG-BLuE
HD-15 PIn 5
13
VGA, AnALoG, GnD
HD-15 PIn 6
8
VGA, AnALoG-rED, GnD
HD-15 PIn 7
8
VGA, AnALoG-GrEEn, GnD
HD-15 PIn 8
8
VGA, AnALoG-BLuE, GnD
HD-15 PIn 10
13
VGA, SYnC-GnD
HD-15 PIn 13
7
VGA, H-SYnC
HD-15 PIn 14
12
VGA, V-SYnC
HD-15 PIn
SHELL
9
VGA, oVErALL SHIELD
➊
➌
➋
PIn 1
PIn 2
PIn 7
PIn 17
Marine Video Cable
End View