Garmin GTS 8000 Replacing Download

Page: 15 / 16

Version 1.0

Appendix B Configuration ID / CRC Numbers

This section will provide details on determining the correct configuration ID or CRC number for

a particular M2 aircraft based on the installed options. Through the rest of this section the

number will be referred to as a CRC number for simplification.

Note:

Radar trims that are not at zero for both pitch and roll will cause the number to be

different. Ensure they are at zero before verification.

Note:

Once the CRC number is verified, then the radar trims can be adjusted to the original

values. See section 4 for details.

Every combination of options that have been ordered or delivered is listed. If you have an

aircraft that has been modified in the field that now has a combination not listed, please

contact Team M2 at

teamm2@txtav.com

Each option is assigned a letter to ensure accuracy when comparing the combination of

options to the final number.

Options

Single GSR 56 (includes GDL 59)

Dual GSR 56 (includes GDL 59)

GDL 69

WX-1000 Stormscope

Becker ADF

GDR 66

HF 9000

Cabin Briefing

GSR 56 Weather

DME 2

Unlock Cards

Synthetic Vision (SVS)

TAWS Class A

TCAS II

Windshear

Doppler & Turbulence

CPDLC

Example:

Aircraft has Single GSR, GDL 69, Becker ADF, GDR 66, GSR 56 Weather, SVS, and

TCAS II. Its code should be

ACEFKNR

. This equates to a CRC number of 450CB913.

Summary of Contents for GTS 8000

















Search results

Summary of Contents for GTS 8000

Reviews:

Related manuals for GTS 8000

Brands by name

Popular brands

Garmin GTS 8000, Replacing

Search results

Summary of Contents for GTS 8000

Reviews:

Related manuals for GTS 8000

Brands by name

Popular brands