background image

Individual Routine Calls

When you connect the chartplotter to a Garmin VHF radio, you 

can use the chartplotter interface to set up an individual routine 

call.
When setting up an individual routine call from your chartplotter, 

you can select the DSC channel on which you want to 

communicate. The radio transmits this request with your call.

Selecting a DSC Channel

NOTE: 

The selection of a DSC channel is limited to those 

channels that are available in all frequency bands. The default 

channel is 72. If you select a different channel, the chartplotter 

uses that channel for subsequent calls until you call using 

another channel.

1

Select 

Info

 > 

DSC List

.

2

Select a vessel or a station to call.

3

Select 

Review

 > 

Call with Radio

 > 

Channel

.

4

Select an available channel.

Making an Individual Routine Call

NOTE: 

When initiating a call from the chartplotter, if the radio 

does not have an MMSI number programmed, the radio will not 

receive call information.

1

Select 

Info

 > 

DSC List

.

2

Select a vessel or a station to call.

3

Select 

Review

 > 

Call with Radio

.

4

If necessary, select 

Channel

, and select a new channel.

5

Select 

Send

.

The chartplotter sends information about the call to the radio.

6

On your Garmin VHF radio, select 

Call

.

Making an Individual Routine Call to an AIS Target

1

From a chart or 3D chart view, select an AIS target.

2

Select 

AIS Vessel

 > 

Call with Radio

.

3

If necessary, select 

Channel

, and select a new channel.

4

Select 

Send

.

The chartplotter sends information about the call to the radio.

5

On your Garmin VHF radio, select 

Call

.

Gauges and Graphs

The gauges and graphs provide various information about the 

engine and environment. To view the information, a compatible 

transducer or sensor must be connected to the network.

Viewing the Gauges

1

Select 

A/V, Gauges, Controls

.

2

Select a gauge.

3

Select   or   to view a different gauge page.

Changing the Data Shown in a Gauge

1

From a gauges screen, hold a gauge.

2

Select a data type.

3

Select the data to display.

Customizing Engine Gauge and Fuel Gauge Limits

You can configure the upper and lower limits and the range of 

desired standard operation of a gauge. When a value exceeds 

the range of standard operation, the gauge becomes red.

NOTE: 

Not all options are available for all gauges.

1

From the engine gauges screen, select 

Menu

 > 

Gauge 

Setup

 > 

Set Gauge Limits

.

2

Select a gauge.

3

Select 

Mode

 > 

Custom

.

4

Select an option:
• To set the minimum value of the standard operating 

range, select 

Rated Min.

.

• To set the maximum value of the standard operating 

range, select 

Rated Max.

.

• To set the lower limit of the gauge lower than the rated 

minimum, select 

Scale Min.

.

• To set the upper limit of the gauge higher than the rated 

maximum, select 

Scale Max.

.

5

Select the limit value.

6

Repeat steps 4 and 5 to set additional gauge limits.

Viewing Engine and Fuel Gauges

Before you can view engine and fuel gauges, you must be 

connected to a NMEA 2000 network capable of sensing engine 

and fuel data. See the installation instructions for details.

Select 

A/V, Gauges, Controls

 > 

Engines

.

Selecting the Number of Engines Shown in Gauges

You can show information for up to four engines.

1

From the engine gauges screen, select 

Menu

 > 

Gauge 

Setup

 > 

Engine Selection

 > 

Num. Engines

.

2

Select an option:
• Select the number of engines.
• Select 

Auto Configure

 to automatically detect the number 

of engines.

Customizing the Engines Shown in Gauges

Before you can customize how the engines are shown in the 

gauges, you must manually select the number of engines 

(

Selecting the Number of Engines Shown in Gauges

).

1

From the engine gauges screen, select 

Menu

 > 

Gauge 

Setup

 > 

Engine Selection

 > 

Edit Engines

.

2

Select 

First Engine

.

3

Select the engine to display in the first gauge.

4

Repeat for the remaining engine bars.

Enabling Status Alarms for Engine Gauges

You can enable the chartplotter to display engine status alarms.

From the engine gauges screen, select 

Menu

 > 

Gauge 

Setup

 > 

Status Alarms

 > 

On

.

When an engine alarms is triggered, a gauge status alarm 

message appears and the gauge may become red depending 

on the type of alarm.

Enabling Some Engine Gauge Status Alarms

1

From the engine gauges screen, select 

Menu

 > 

Gauge 

Setup

 > 

Status Alarms

 > 

Custom

.

2

Select one or more engine gauge alarms to turn on or off.

Setting the Fuel Alarm

Before you can set a fuel level alarm, a compatible fuel flow 

sensor must be connected to the NMEA 2000 network.
You can set an alarm to sound when the total amount of 

remaining onboard fuel reaches the level you specify.

1

Select 

Settings

 > 

Alarms

 > 

Fuel

 > 

Fuel Level Alarm

 > 

On

.

2

Enter the remaining amount of fuel that triggers the alarm.

Setting the Fuel Capacity of the Vessel

1

Select 

Settings

 > 

My Vessel

 > 

Fuel Capacity

.

2

Enter the combined total capacity of the fuel tanks.

26

Gauges and Graphs

CONFIDENTIAL

Summary of Contents for M5APGT00



















































Reviews: