Garnet MULTIRACK 688-S Manual Download

Page: 6 / 14

Page 6

688 Manual

The PERMIT diagnostic LED will light when the controller is in

permit and is connected to either an optic or thermistor rack. It

will not illuminate if the controller is not connected, since the rack

is the controller power source.

WARNING: To maintain overfill protection, the operator

MUST verify float movement of the

EVE

(or

EVE

PECIAL

) at the start of loading each compartment. If any

skipping of calibration points is observed, discontinue loading

until the problem is corrected. Please refer to the manuals for

these instruments for further details.

Installation

Installation of the system consists of connecting the appropriate

module into the gauge and programming alarm point 4. The

controller enclosure is mounted, connected via fiber optic cable

to the module, and wired to the rack sockets(s). Verification of

system operation completes the installation.

Summary of Contents for MULTIRACK 688-S















Search results

Summary of Contents for MULTIRACK 688-S

Reviews:

Related manuals for MULTIRACK 688-S

Brands by name

Popular brands

Garnet MULTIRACK 688-S, Manual

Search results

Summary of Contents for MULTIRACK 688-S

Reviews:

Related manuals for MULTIRACK 688-S

Brands by name

Popular brands