background image

 

 

 

TREND ARROWS 

 
The main unit display shows arrows next to the measured values. These arrows show the trends of the 
measured values 
 

 

 

 

increase              steady state              decrease 

 

SETTING OF UNITS 

 

°C and °F

 

In the basic display mode, press 

/CF

 briefly to switch the displayed measured temperature units to °C 

or °F

 

 

TIME AND DATE CONTROLED BY THE DCF-77 RADIO SIGNAL 

 

The weather station is equipped with the DCF-77 time/date control signal receiver. The DCF-77 is 
broadcast by a transmitter from Frankfurt am Main, Germany, with a range of about 1500 km. The time and 
date is adjusted every day. In case of poor reception conditions time and date can be adjusted manually.  
After time and date have been adjusted manually, they will be readjusted upon reception of the DCF-77 
signal. 
 
When the batteries are inserted into the main unit and the wireless sensor and the connection is 

established, the main unit will start to receive the DCF-77 signal. The DCF-77 signal reception icon 

starts 

flashing. If the signal is not received, the DCF-77 signal reception icon will not be shown on the display. 

Upon successful reception the reception icon 

 

 

will be displayed on the display, if the signal is not 

received, icon 

 

will be displayed. 

The DCF-77 signal is receiver every day

 

at 1:03; if date/time are not 

adjusted then also at 2:03, 3:03, 4:03 and 5:03. 

Reception of the DCF-77 signal can be started manually by pressing and holding the 

/CF

 button for 3 

seconds. Receiving and adjusting time can take up to 10 minutes. The DST label next to the time indicates 
the daylight savings time. 

 

MEMORY FOR MAX AND MIN MEASURED VALUES 

 

The main unit is equipped with memory for maximum and minimum measured values. Press the 

/MEM

 

button repeatedly to display the maximum and minimum measured values of the indoor and outdoor 

temperature and relative humidity. MAX or MIN is displayed on the display. Press and hold 

/MEM

 for 3 

seconds to erase the memory. 
The memory is also automatically erased at 00:00 every day 

 

ALARMS FOR THE UPPER AND LOWER LIMITS OF THE OUTDOOR TEMPERATURE 

 

For the outdoor temperature it is possible to set the upper and lower limit alarm in the range from -40 °C to 
+ 70 °C, separately for each channel. 
Select the required channel with the 

CHANNEL

 button. Press and hold the 

ALERT

 button on the rear of the 

main unit for 3 s. The icon  

 is displayed and the upper temperature limit value starts flashing.  Use the 

/MEM 

or 

/CF

 buttons to set the required temperature upper limit. Press the 

ALERT 

button briefly. 

The icon 

 is displayed and the lower temperature limit value starts flashing.  Use the 

/MEM 

or 

/CF

 

buttons to set the required temperature. If you hold the 

/MEM 

or 

/CF

 buttons, the values will change 

faster.

 

Press 

ALERT 

to confirm the setting.

   

 
 
 

Summary of Contents for 525










Reviews: