For use on doors 1 3/8" to 1 3/4" (35 mm-45 mm) thick
Adjustable latch for 2 3/8" (60 mm) and 2 3/4" (70 mm) backset
Backset is a distance from door edge to centr of hole on
door face.
Some locks are supplied with adjustable latch which can fit
2 3/8" (60 mm) or 2 3/4" (70 mm) backset.
Follow the steps shown below to change backset.
e
Rotate
illustrated below,
Latch backset adjustment
the latch case as
for backset 2 3/4" (70 mm) or reverse
direction for 2 3/8" (60 mm).
Template
®
45
40
35
Mark 1" (25.4mm) hole at center of door edge.
For 2 3/8" (60 mm) backset
For 2 3/4" (70 mm) backset
ø
(
)
2 1/8" 54 mm
Fold on dotted line and fit on door edge
1 3/4"
1 3/8"
1 9/16"
INSTRUCTIONS FOR INSTALLATION
OF DEADBOLT LOCK
Installation
Installation
IMPORTANT
: Please read this manual carefully
before installing this deadbolt lock and save it for reference.
Toll-free
Number: 1-800-268-6591
model no.: 046-5631-0 & 046-5688-6 & 046-5690-8
180°
2 3/4" (70 mm)
2 3/8" (60 mm)
70 mm
60 mm
To change latch face
the faceplate from backplate.
2. Snap the selected faceplate onto backplate.
1. Use a flat-head screwdriver to separate
Drive in installation
Make sure the round faceplate is
properly aligned as illustrated and
snap it to the latch case.
Installation
Drive-in latch
1. Mark the door with template
Select 2 3/8" or 2 3/4" (60 mm or 70 mm) backset
as desired and mark centre of hole on door face.
c. Insert latch and tighten screw.
d.
For drive in latch, drill 1" (25.4 mm)
hole and press latch until it is flush
with door edge.
3. Install latch
a. Insert latch in hole and keep it parallel
to door face.
Mark outline of face plate and remove
latch.
b. Chisel 5/32" (4 mm) deep inside
traced outline or until face plate
is flush with door edge.
a
c
b
d
a
b
c
4. Install strike
c.
Install strike and
tighten screws.
a. Close the door so the latchbolt is against the door frame.
b. Measure one half of door thickness from door stop
and vertically mark center line of strike. Drill 1"
(25.4 mm) hole, 1" (25.4 mm) deep at intersection of
horizontal and vertical line of strike. Mark outline
using strike plate and chisel 5/64" (2 mm) deep for
strike.
5. Install single cylinder exterior mechanism
Press cylinder side flush against door making certain the
tailpiece is properly positioned in latch crank. Tapped
holes in housing of exterior cylinder should be lined up
with screw holes. Key hole should be in down position.
TAILPIECE SHOULD BE HORIZONTALLY INSERTED INTO
LATCH CRANK.
6. Install single cylinder interior mechanism
a. Slide turnpiece and interior rosette.
b. Insert both flanges into the hole on the door face.
Make sure the flanges stay in the hole when fastening
screws.
c. Insert machine screws through holes in cylinder and
tighten firmly.
8. Install interior cylinder (double cylinder)
Latch adjustment
2. Drill holes
a. Drill 2" (51 mm) hole through door face, from both
sides to avoid wood splitting.
b. Drill 1" (25.4 mm) hole for latch
(refer to step 3d for drive-in latch).
7. Install exterior cylinder (double cylinder)
a. Press interior assembly flush against door, making certain
the tailpiece is properly positioned in latch crank.
Key hole should be in down position.
b. The interior tailpiece
inserted into the exterior
blade.
must be
c. Insert two screws through countersunk holes
in exterior cylinder and tighten firmly.
Press exterior cylinder flush against door.
Exterior tailpiece should be horizontally inserted
into latch crank first.
a
b
c
a
b
c
G
-
LT
-
01
