ANITA ©
MP00100EN_170907
6
Important notices
Be careful!
Never set off the machine without the belt cover, you could be heart.
To avoid disorders and damages, i tis necessary to do these:
Before the first setting off, clean and oil the machine properly .
Check if the mains voltage is the same like the voltage written on the motor rating
plate. If it isn´t, never set off the machine .
When the machine is running the handwheel, must be turned towards the person, If
it isn´t, the motor reverse polarity.
Don´t run the machine more than 3/4 its speed in first two weeks
When you put the produkt off the machine put the needle bar to its highest positron.
Safety instruction:
1.
The machine can be used for it is needed. When you need to use different
embodiments it is necessary to do all safety instruction.
2.
It isn´t allowed to run the machine without protective diveces which it has from the
manufacturing plant
3.
Only edification person can set the machine off and work with it.
4.
When replacing sewing machines (needle, presser foot, throat plate, feed dog and
bobbin, must be disconnected main switch.
5.
Only experts can do wiring
3. COMMISSIONING THE MACHINE
To avoid disorders and damages of the machine you must do these:
Clean the machine from preservatives and put one or two drops oil to the hook remove the
front cover and oil connecting rod, needle bar and thread lever. An expert must try if the
electric equipment is all right including the electric voltage for motor and the handwheel of
the machine must be turned towards the person (according to arrow). Don´t use the highest
speed of the machine in first two weeks sew to 3/4 the highest speed.
Be careful
Don´t encroach the electric equipment of the machine, call an expert. There is a danger of
elektricity.
When you work with the machine or you are at it you must behave not to be hurt.
No liquid can be put into the electric equipment, it could be disordered. It is necessary to
pay attention to safety instructions.
www.garudan.cz
Summary of Contents for anita GC-3317 Series
