background image

© ANITA 

 

MP04300EN_200610 

GF-140, GF-240 Series 

 

B

 

SAFETY INSTRUCTIONS 

 
Read the instructions carefully before installation and use. Keep this manual for future 
reference. 

B1.

 

GENERAL INSTRUCTIONS 

1.

 

Do not operate the sewing machine until proper preparation has been made by a 
technician or qualified person and safety precautions have been taken. 

2.

 

Always follow the safety instructions when handling the machine. 

3.

 

This sewing machine may only be operated by properly trained personnel. 

4.

 

Maintenance, repair, inspection, and adjustment of the machine may only be carried 
out by a qualified person. 

5.

 

Work on electrical equipment may only be performed by a qualified worker or person 
with the appropriate authorization. Work on electric parts and equipment on your own 
is not permitted. 

6.

 

The machine may only be used for its intended purpose. 

7.

 

The warranty does not cover any problems in the operation of the machine that are 
caused by unauthorized modifications to the machine, as well as problems caused by 
non-observance of the instructions given in this manual and generally known habits for 
the operation and maintenance of industrial sewing machines. 

B2.

 

INSTALLATION PRECAUTIONS 

1.

 

Immediately report visible damage to the carrier. Check the contents of the order 
shipment and report any defects immediately to the manufacturer. Later claims will not 
be accepted. 

2.

 

Use the machine after checking that it meets all the safety standards of your country. 

3.

 

The machine head is covered with a corrosion-proof coating. Wipe off the lubrication 
and dust layer with a cloth or petrol before placing it on the work surface. 

4.

 

The machine has been thoroughly inspected and tested before shipment. However, it 
may have been damaged by transport or impact. Check the operation of the machine 
with the handwheel, to detect extraordinary noises, heavy running, etc. before starting 
the test sewing. 

5.

 

Never start the machine if the oil level is under or over the marked lines. 

6.

 

Check that the power and phase are in accordance with the label instructions. 

7.

 

Proper grounding of the machine is necessary. 

8.

 

Use the correct grounding plug. 

9.

 

Do not use an extension cord. 

10.

 

Make sure that the power supply and voltage match the requirements on the label of 
the machine. 

11.

 

Do not use the machine in explosive or corrosive environment. 

12.

 

In the first two weeks, do not exceed 3/4 of the maximum machine speed. 

 

 

 

www.garudan.cz

Summary of Contents for GF-140 Series












































Reviews: