© ANITA
MP03100EN_180912
5
2.
Machine installation:
Physical damages such as functional difficulties or breakdowns may occur depending
on installation conditions of the machines. Be sure to heed the following conditions.
Caution
a)
Remove the packing from top to bottom
b)
Install a climate controller and clean it regularly to prevent dust and moisture build-up from
contaminating and corroding the machines
c)
Keep the machines away from direct sunlight.
d)
Keep a minimum distance of 50 cm between the machine at both sides and backside and the
wall to secure sufficient space for repair.
e)
Do not operate the machine near areas with danger of explosion. Refrain from running the
machine in the vicinity of risky places, e.g., where a large quantity of aerosol-spraying products
or oxygen are handled, unless specific guarantees are given otherwise for the operation of the
machine to prevent explosion at such places.
f)
The user should install an illuminator in the work area for the machine not come supplied with
any lighting apparatus due to the specific features of the machine.
[Note] Details of the machine installation are laid out in section 2) Installation.
3.
Troubleshooting:
When the machine is in need repair, only our authorized service technicians must
handle it.
Danger
a)
Before cleaning and repairing the machine, shut off the power supply and wait four minutes
for the machine to discharge completely.
b)
Not part of the machine or specifications may be modified without prior consultation with
our company. Any such modification could risk safe operation of the machine.
c)
In case of repair, replace only with original Garudan parts from Anita.
d)
After repair, put safety covers back on the machine.
4.
Machine operation:
GF-3131 series are intended to be used for industrial purposes for sewing textiles and
other similar materials. Carefully study the following instructions before operating the
machine.
Caution
a)
Read the manual thoroughly and understand the instructions fully before use.
b)
Put on proper safety garments.
c)
While the machine is in motion, keep your hands or any part of your body away from moving
parts, e.g., needle, hook, thread take-up spring and pulley, etc.
d)
Do not remove any form of safety covers while the machine is in use.
e)
Be sure to connect the ground (earth) wire.
www.garudan.cz
Summary of Contents for GF-3131-447 MH
