© ANITA
MP03200
EN_180810
23
11.
Sensors for initial position of X, Y and Z axis:
Default setting for initial position
of X and Y axis initial point and position of Z
axis (needle) is set in
the production plant.
a)
Sensors are placed on the machine arm, under left cover of the linear railway (Fig. 32).
b)
X axis movement position can be set by moving sensor plate (2) against the sensor (1).
c)
X axis movement position can be set by moving sensor plate (3) against the sensor (4).
For setting of initial points on X and Y axes move the feeding plate to its central position in both
axes. Initial point refers to the actual center position of the feeding plate towards the needle. In
this position the edges of sensor plates (2) and (4) are in line with the middle of sensors (1) and
(3) (like the edge of sensor plate on Fig. 33).
d)
Sensor of Z
axis is located in the machine head and it can be reached after taking off cover of
the machine head. Revolving sensor plate (5) is located on the main shaft.
Put the needle in the lower stop position and make the
s
etting of the sensor plate (5) located on
the ring as is illustrated on the
F
ig
.
33
–
the sensor plate is in the middle of the body of the
sensor (6).
Clearance between sensor and sensor plate should be set for the value 0.3
– 0.
5 mm.
Fig. 32
www.garudan.cz
Summary of Contents for GPS/X-3525 Series
