© ANITA
MP04600EN_220920
GZ-5525 series
21
E2.
THE HOOK LUBRICATING CONDITION ADJUSTMENT
Refer to the above picture.
To adjust hook lubricating through screw A which site before oil tank of hook.
The oil quantity is lowest when screw A was turned with clockwise and the arrow points to „0“
position.
The oil quantity is highest when screw A was turned with anticlockwise and the arrow points to
„MAX“ position.
E3.
MACHINE CLEANING
The hook, feed dog and other parts of machine should be cleaned daily, and drop two or three coal
oil into hook and other parts that need to be lubricated. Clean all the spilth after ending of highest
speed operation of machine, then lubricate the machine with oil. The clean work must be insisted
every day. (Especially the machine worked one week, the clean work is very important, as the spilth
will affect the sewing capability and rust hook and machine. The bobbin should be taken away from
the hook before cleaning.)
Maintenance of motor: clean dust of the motor cover each one month or two months. (More dust or
sundries of motor cover will make it too hot.)
Maintenance of control box: clean dust of the connector. (It will affect accidental operation if there
are more dust on the connector.)
Warning!
Before cleaning and lubricating the machine, be sure to switch off all switches and hold
your feet away from the machine foot-pedal in order to avoid accidental machine start by
pedal.
Summary of Contents for GZ-5525 Series
